6V vs 3.7v

[MichaelOz]

I'm looking at getting a new PV, one that really sticks out as a good quality unit is the ProVape (ProVape Electronic Cigarette Battery Mods, Atomizers and Accessories). It is however a 3.7v device. Up until now I've only used a 510 and an Ego, both of which are 3.7v. So I have no direct experience with higher voltage.

I do own 1 LR atty, so as they say up the voltage or lower the resistance. However this is theory, I would like to know from you guys who own 6v mods, is it really that much better than a 3.7v device?

If yes, its mind blowingly better, I want a mod that is really good quality, possibly something that can double as a 6v and also a 3.7v.

Really interested to hear what you all have to say, thanks in advance.

 

[lexgar]

Hello Michael.

I have the ProVape-1 with updated switch as well as a Black Silver Bullet and a BB. I use them all depending on where I am going to be. The ProVape is my daily carry switching off with the BB depending on my mood. The BSB stays on my desk due to the size.

As to 6v vs 3.7 with a LR atty, that also depends on my mood. With the BSB and the BB, I can get 6v with the proper batteries and I have them for both devices. The vapor is hotter and with increased volume at 6v. Sometimes I just want more, but in reality it is not often. The difference is there, but not to the point that I often am willing to deal with the much more frequent battery changes. The 15270 batteries that fit in the BB only last for a few hours and the RCR123a in the BSB perhaps 3 or 4 hours. As always, your mileage may vary.

Certain juices taste better (or worse) with 6v. All the flavor can just be burned away at higher voltage. The amount of power to the atty also varies with different devices. I do not have a multimeter, but my taste buds tell the tale. The ProVape has slightly less power (according to the vapor) than the BSB or BB with a hotspring. Perhaps it is that the aluminum body and copper spring are a bit better than the SS in the ProVape. When I put a copper spring in the ProVape, I did notice a difference.

Sometime this week past, I saw a post about power that compared the different attys at different resistance with the power out to the atty. It showed just what you can get with different attys and batteries. Not sure what the title was. but great information.

To me, 3.7v with a LR atty (1.8-2.0 resistance) is my sweet spot and you will not go wrong if you choose the ProVape. Great device and great customer service as well. I like the Stainless Steel construction which is why it is my go to device for being out in the world. I do not worry about scratches and dings like I do with the aluminum PVs. Just my $.02

 

[debb]

I second the Provape...used with a lr atty...it is awesome!

 

[BradSmith]

I really prefer either 5 volt or a low resistance atty or cartomizer. It's the watts that is important. A five volt with a standard atty heats the coil using 10watts this is just about the same as using a low resistance atty or caromizer on a 3.7 volt unit. The problem with most units that use batteries that produce more power is the resistors that are used to bring the power down to the right level do so by burning off the energy in the form of heat. This is a waste of power and reduces the life of the batteries. Also if you go with higher voltage mods you will either go through atties more quickly (like putting a 30 watt bulb in a 50 watt socket) or need to use high resistance atties which reduce the wattage and basically leave you with the same effect as a 3.7 volt anyway.

I was really hooked on 5 volts for a while, but I have now been using the new low resistance cartomizers on a 3.7 volt box mod. they are cheap easy to refill and last me as long as my atties were with less filling up and dripping time.

So I guess I would suggest the 3.7 volt mod. The 14500 batteries are also a plus, they last a long time and are cheap enough to replace.

 

[MichaelOz]

Thanks guys, it seems the 3.7v Provape is the PV I'll buy.

 

[rockgod]

I just got the provape with some LR cartos and attys to try out. The unit is very well made, but I can't seem to get any more vapor using an LR atty/carto when compared to my ego batts, in fact it seems the egos produce just a bit more vapor. I've tried different pg/vg mixes and vendor juices and the results are always the same.
I do have a multimeter and the voltage is in the right range (a little over 4v at full charge and settling down to 3.7 when vaping).

Thoughts anyone?

 

[scubasteve25]

i honestly enjoy 5/6 v vapeing i cant even use my sabertouch at 3.7 just seems too weak now

 

[Vaporologist]

i honestly enjoy 5/6 v vapeing i cant even use my sabertouch at 3.7 just seems too weak now

I'm with you. Everyone has their own definition of what is the sweet spot and for me 6V with a 3.5 ohm atty is the way to. Anything less and I chain vape because I don't get the real satisfaction. 3.7V with LR atty is in that 9ish watt range and just doesn't do it for me. I still use a 3.7V setup when I feel like pleasure-vaping or need something small to carry when on-the-go, but that's it.

6V vaping has helped me cut down on my liquid consumption from 6-7ml per day down to about 4ml per day and from 36mg to 18-24mg. I take 4-5 powerful hits and can lay the PV down for a while since I got the satisfaction needed.

 

[mokeyjoe]

I used to really like my 5v passthrough but the more I vape the less voltage is important. I prefer my eGo now at 3.2v, and that's not even with an LR atty.

I get plenty of vapour with the VG liquids I use, and as far as throat hit (or general sensation) goes I find the warmth of vapour is the most important factor for me. Perhaps it's the cone, or the steel tips I use, or my vaping technique, but I find after the first couple of drags the atty really starts to heat up nicely. My 5v passthrough can get a little too hot with the way I vape.

I find if I break my atties in for a few days on my passthrough the performance on the eGo improves, so I always do this now. I did try an LR atty once, but I couldn't tell the difference to be honest.

 

[Liv2Ski]

Thanks guys, it seems the 3.7v Provape is the PV I'll buy.

I ordered mine 10/8. Just my luck Columbus day weekend. Sort of hoping it would be here today. Oh well

 

[rhsmitty]

It's my understanding that the 510/eGo batteries actually operate at 3.2v under load so a 3.7 mod using a 3.7v battery like the 14500 DOES produce more wattage and more vapor. I use a 14500 box mod with a standard atty and am very happy and it is better than standard 510 or ego battery. Sometimes I like a LR atty like the 306LR but sometimes it is just to much.

The ego mega atty and carts do seem to produce better vapor than standard atty's probally due to a larger coil and bridge but it is still 3.2v.

Just my observation. Any vet's feel free to correct.

 

[MichaelOz]

Yes, this is a very good point. As you say a 510 / Ego won't give you true 3.7v OOB. So I am sure battery mods will do better , for example the Provape or real screwdriver.