Afsv3

[HoPeFuLLL]

Parallex2, the vid gives you the basic idea but now I think Imeo has come round to filling the AVS off the GGTS using side of palm to block the bottom hole. This has big advantages and when you screw it all up tight the excess liquid is not forced into the collection tank so when you have a 100% sealed AVS and put it back on you are good to go straight away, no pulling it back off to empty the CT.

 

[Skyway]

I have a question about the AVS3. How do you control the amount of ejuice that drops down into the collector tank? Mine drips down there too much and I have to take the 2 apart and put what is in the control tank back into the reservoir tank. The other question I had was I have heard that VK has atty specified for the GG but I have never seen them. Can any 510 pretty much work? Does the O-ring in the mouthpiece suppose to be a tight fit to the atty? Mine does not really look like it is making a tight fit so if I were to lay it on its side, juice might find a way around the atty into the mouthpiece theoretically.

 

[HoPeFuLLL]

I have a question about the AVS3. How do you control the amount of ejuice that drops down into the collector tank? Mine drips down there too much and I have to take the 2 apart and put what is in the control tank back into the reservoir tank. The other question I had was I have heard that VK has atty specified for the GG but I have never seen them. Can any 510 pretty much work? Does the O-ring in the mouthpiece suppose to be a tight fit to the atty? Mine does not really look like it is making a tight fit so if I were to lay it on its side, juice might find a way around the atty into the mouthpiece theoretically.

Not sure what you are using. 510? 3.7V?

Juice in the collector tank is usually because you don't have 100% seal. If your seal is good you should be able to remove the AVS from the GGTS (CT) and it wont drip from the bottom hole (no need to put finger on mouthpiece hole). Try it.

 

[RippleInStillWater]

Look at the wiki at the diagrams to make sure you have all the correct o-rings -- it helped me!

 

[imeothanasis]

I have a question about the AVS3. How do you control the amount of ejuice that drops down into the collector tank? Mine drips down there too much and I have to take the 2 apart and put what is in the control tank back into the reservoir tank. The other question I had was I have heard that VK has atty specified for the GG but I have never seen them. Can any 510 pretty much work? Does the O-ring in the mouthpiece suppose to be a tight fit to the atty? Mine does not really look like it is making a tight fit so if I were to lay it on its side, juice might find a way around the atty into the mouthpiece theoretically.

collector tank was made to collect liquid Sky my friend. If atties didnt leak then no reason to make the CT. But all atties are made to leak. So if you see that CT is full after too many inhales you can empty it. But if you see that the CT gets full very quickly then you have to check if AVS tank leaks when its out of CT. So unscrew the AVS and see if it leaks. If yes, then you have to screw harder the 510 connector into the tank. I hope that you didnt unscrew the pin of 510 when you receive it and you use it as it came.

please tell me your results

 

[Skyway]

Well, to be honest I just now found out what the little silver thing that came with the AVS was. I could not really find out what it was until I looked up on VK site about it being an extension for the 510 atty to reach the top mouthpiece. I will play around with that to see if that was the seal problem.

 

[imeothanasis]

that was the problem for sure buddy. Overflooding all the time

 

[Poppa D]

Good morning every one. I have a question regarding the AVS V3.
I am trying to increase the flow of liquid to the atomizer. So far I have loosened the ring at the base of the atomizer connection to wide open (inside of the tank), closed/opened the Air control ring tighter/looser (open more air, less liquid?) near as I can tell I have it set for maximum liquid delivery but the vapor seems a bit weak, not as thick as dripping. Is this normal?

 

[HoPeFuLLL]

Possibly a bad connection somewhere? Give your unit a clean and make sure atty is compatible.

 

[Skyway]

What battery / atty combo are you using? 3.7,6v LR, SR HR

 

[imeothanasis]

all the above questions from hope and Sky are right poppa but I have one more for you. Do you hear gurgling sound? Atomizer produces less smoke if when its not feeded good but also when its overflooded too

 

[Poppa D]

I'm using it with a buzz, 510 2.8 ohm. The voltage I like is 4.5 to 5, all volts seem to be sensitive extra wattage with the AVSV3 attached. Thanks for responding.

What battery / atty combo are you using? 3.7,6v LR, SR HR

 

[one_raven]

Ignore me, imeo answered in another thread.

 

[Poppa D]

nope no gurgling. its very quiet, its nice in that regard. It works well but seems to be prone to running dry rather than wet.

 

[imeothanasis]

if you empty the CT then you will not hear it any more one

 

[imeothanasis]

nope no gurgling. its very quiet, its nice in that regard. It works well but semms to be prone to running dry rather than wet.

Liquid is too low maybe?

 

[Poppa D]

No liquid is full.

Sent from my DROIDX using Tapatalk

 

[imeothanasis]

keep the CR open about 1/4 of a full turn from the closed position poppa.

 

[Skyway]

If the liquid is full but the atty is running dry, about the only thing I could think would be happening is the nut right below the atty is not allowing any fluid to go into the atty. Is this a clean atty? Maybe your breather holes on the side of the atty are clogged.

 

[Poppa D]

I have tried 3 different attire so far, all new, I'll keep at it for a while.

Sent from my DROIDX using Tapatalk