All my mods part1

[slopes]

I don't think anyone here has anything less than a huge admiration for Raidy's work. I also think everyone takes him at his word that the Genesis design works very well. But - as he has shown - the Genesis comes in all shapes and sizes and I hope that Raidy won't mind at all when people seek out his expert opinion and advice on a planned version. It would be crazy to waste hours and hours of time making something when a simple question to Raidy first might show it to be useless.

 

[stouchon]

I personally don't mind the "clutter", this is a discussion forum. I would like to see as many on the ideas as possible.

@slopes
You said that my idea on the e2 style would not wick as well. if you could bend your coil in /\ shape instead of --, you could still keep the initial design and have two wicking sources.

 

[slopes]

@stouchon - your idea might well work. It's similar to what I have suggested to Bad - over on the E2 thread - as a possible development of his PTB mod.

 

[nubee]

Tell me about it. I am working on a bottom cap for the laxan tubing, I don't have a lathe but I am very clever with my drill press. It's just that I will spend hours (perhaps days) doing something with it that I could do in 3 min.s with the proper tool.

Pics or (as they say) it didn't happen

 

[raidy]

If you go into your profile there is a link below your picture that says 'find all posts'.

does that help?

Yeah, it helps. Thank you!!

 

[Dogzlife]

Raidy, incredible work!!! Just what kind of mods do you dream about??

By the way, does the mash wick well with either a full or nearly empty cylinder? Have you noticed practical limitations in the length and/or cylinder diameter of the mash?

Again, really incredible stuff!!!

 

[raidy]

Ideal genisis parameters

This are the ideal paramters if you wish:
good vapour, not too much throat hit, not to much battery power and WONDERFULL Taste.
The mash should be rolled with nearly empty cylinder inside.

if you are a throat hit fan: 325 mesh, 0,2mm kanthal ~3cm = 2A.

Function of the small stainless steel tube: more constant liquid flow, whatever the liquid level is. length=25mm

 

[WillyB]

I wouldnt expse the positive or the negative wires to any fluid... Thats what i would do, and it looks like he did this also. I doubt he would let the insulation around the wire be exposed to fluid, and it doesnt look like he does either.

Well there's theory and there is actual use. Bulli's A-1 is quite popular and by all reports works well.

Here's a view without the top piece and juice cart. The fiber goes up into the cart (works like the bridge/wick of an atomizer). The design is very similar to the GreenCig and Joye cartos.

 

[theECB]

This looks like a great site for tubing and also sells "delrin" rods which could easily be made into the end caps for the tank as well.
Interstate Plastics

 

[Gummy Bear]

Pics or (as they say) it didn't happen

I have been on this all day. (when I wasn't looking for the "My Posts" button) Cutting down a blank of 1"OD alum bar stock. (would have only took 5 min.s with a lathe. I have left it a red hair large for now, (Raidy, that is an official American measurement) untill the lexan tube comes in so I can make sure I'll get the standard "Gudentite" German fit.
(or is that the standard German torque spec).

 

[raidy]

My DreamPipe with genisis atty in action

You asked for a video. Here it is:



Maximum Power is ~1.4A-1.6A!! Same as a PEN, but look the vapour!

Now you see, THAT a genisis realy works, and how it works!

greetings Raidy


The "my posts" button is back Welcome lovley button

 

[OgreLokon]

I started reading this thread this morning.... wow... just... WOW! You good sir are an artist.

I seriously feel like I crammed an entire semester of college into a single day.

 

[peaceoffcake]

Impressive. But I'm little bit confused. Why regular atty's produce no vapor when we press the button? They produce vapor only when we inhale.

 

[Gummy Bear]

Sweet,,, That's what I want. enough vapor to choke a horse.

 

[raidy]

Impressive. But I'm little bit confused. Why regular atty's produce no vapor when we press the button? They produce vapor only when we inhale.

This is a gensis, a complete new and other system of atty. And ist works in an complete other way. A "normal" atty need a "air-flow" to make the vapour. The genisis can also make vapour without air-flow. But on open "nomal" atty also make a little vapour.

 

[peaceoffcake]

OK. Thanks.
I buy kanthal, I buy mesh, I buy silver wire, tomorow I will buy acrylic tubes. Then I go to my turner
Is aluminum OK? I mean for body?
I intend to put the silver wires that pass through e-liquid in Heat Shrink tube. Is that ok too?

 

[WillyB]

OK. Thanks.
I buy kanthal, I buy mesh, I buy silver wire, tomorow I will buy acrylic tubes. Then I go to my turner
Is aluminum OK? I mean for body?

You figure t will be about a month till you are selling them?

@ Raidy

You gave out way too many technical specs. You should have just provided the concept.

You'll soon see them being sold.

 

[raidy]

Video from the vapour-Oktoberfest-Shisa

Normaly the atty is inside the beer mug, and 4 peoples can inhale at the same time.
But the throat hit is much, much to strong. Its absolut funny to see the schocked faces of the testers.

 

[illuxion]

OK. Thanks.
I buy kanthal, I buy mesh, I buy silver wire, tomorow I will buy acrylic tubes. Then I go to my turner
Is aluminum OK? I mean for body?
I intend to put the silver wires that pass through e-liquid in Heat Shrink tube. Is that ok too?

Raw aluminum is a very reactive material and corrodes quite fast, I'm not sure if I'd like to chance vaping with it raw. You should either anodize it or clear cote it. I had a bunch of stuff hard anodized for my subaru and was surprised at how reasonable the prices were.

 

[peaceoffcake]

You figure t will be about a month till you are selling them?

What are you talking about?