Now your going to make me jinx myself
But they could be here tomorrow
or it could take all week! Depending on how well they fed the sled dogs Ammit 25 RTA
- Thread starter Gallant
- Start date
- th_trl_thread_readers 0
- Status
But they could be here tomorrow
or it could take all week! Depending on how well they fed the sled dogs 
So far so good with mine. Great flavor and vapor no leaks at all. I'm pleasantly surprised been s week so far and it's due for a dry burn and re wick. I have no complaints. I do close the jfc and afc when not in use so that could be why no leaking. I'm going to be flying with it Wednesday so we'll give it he ultimate leak test.
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
I'm getting very solid flavor. The only thing that took practice was the wicking. I vape a pretty small 2.5 mm ID coil, the eliquid slots are large. With rayon I fluff the heck out of the tails, then trim so they will just fill the slots at the outside edge of the eliquid inlets (on the bottom side edges of the tank, not just the holes in the deck); doing this I'm getting good eliquid transport, no leaks, and my wick is staying clean (no backflow discoloration).
Last edited:
Well I guess the Canadian Dog Sled Team was feed Well
So Far the Ammit 25 is a lot like a Pharaoh!
It's a lot smaller & more attractive to look at.
The draw is a bit tighter & the flavour seems a bit, just a bit! muted compared to the Pharaoh!
The build quality seems good it comes with 2 pieces of glass but only one of each 2 Mil & 5 Mil.
I like the "goon style drip tip" it came with a top cap adapter for the tip but no goon tip, I purchased them separately
The build deck is a bit smaller & the wire retention system seems a bit more trouble than the clamp, the Pharaoh has.
IMO the side air flow is watering down the flavour that tinny bit! With the Pharaoh it's only bottom Air flow so all the air hits the coil from the bottom not the bottom & side like the 25.
I would like to use them for a while longer before I say for sure, But as of now IMO the Pharaoh is in the lead by a bit
After using them for a while I will post a follow up, with any faults I mite find
BTW I'm in TC Mode, the coil is 2 by 24 wrapped in 30 gauge all Titanium wire
So Far the Ammit 25 is a lot like a Pharaoh!
It's a lot smaller & more attractive to look at.
The draw is a bit tighter & the flavour seems a bit, just a bit! muted compared to the Pharaoh!
The build quality seems good
it comes with 2 pieces of glass but only one of each 2 Mil & 5 Mil.I like the "goon style drip tip" it came with a top cap adapter for the tip but no goon tip, I purchased them separately
The build deck is a bit smaller & the wire retention system seems a bit more trouble than the clamp, the Pharaoh has.
IMO the side air flow is watering down the flavour that tinny bit! With the Pharaoh it's only bottom Air flow so all the air hits the coil from the bottom not the bottom & side like the 25.
I would like to use them for a while longer before I say for sure, But as of now IMO the Pharaoh is in the lead by a bit
After using them for a while I will post a follow up, with any faults I mite find
BTW I'm in TC Mode, the coil is 2 by 24 wrapped in 30 gauge all Titanium wire
Looks great!Well I guess the Canadian Dog Sled Team was feed Well
So Far the Ammit 25 is a lot like a Pharaoh!
It's a lot smaller & more attractive to look at.
The draw is a bit tighter & the flavour seems a bit, just a bit! muted compared to the Pharaoh!
The build quality seems good
I like the "goon style drip tip" it came with a top cap adapter for the tip but no goon tip, I purchased them separately
The build deck is a bit smaller & the wire retention system seems a bit more trouble than the clamp, the Pharaoh has.
IMO the side air flow is watering down the flavour that tinny bit! With the Pharaoh it's only bottom Air flow so all the air hits the coil from the bottom not the bottom & side like the 25.
I would like to use them for a while longer before I say for sure, But as of now IMO the Pharaoh is in the lead by a bit
After using them for a while I will post a follow up, with any faults I mite find
BTW I'm in TC Mode, the coil is 2 by 24 wrapped in 30 gauge all Titanium wire
What I.d.is your coils? It looks to be 3.5mm. My Gold one just arrived today!
Looks great!
Not exactly sure, I'm using a roofing nail for a mandril
Probably about 3.5 to 4 mm
Roofing nail? That's a new oneNot exactly sure, I'm using a roofing nail for a mandril
Probably about 3.5 to 4 mm
Anyone have any seeping or condensation between the AFC and the base causing a ring of juice or condensation on their mod?
I think it might be related to how low my coil is sitting in the deck. I will try and raise my coil a little bit next time I rewick and see if it resolves the issue.
I think it might be related to how low my coil is sitting in the deck. I will try and raise my coil a little bit next time I rewick and see if it resolves the issue.
According to Canada Post mine will be here tomorrow
I didn't set mine up yet but Vaping with Vic from the U.K. Said if you get that seeping on the mod to poke the cotton down further in the juice hole. Let us know how it goes.
My cotton is currently touching the bottom of the juice holes already, but as mentioned my coil sits really low on the deck also.... maybe 2mm above the bottom airflow
I think it can be, it's not hard to deal with being a single coil. It's pretty easy!
Really deciding what rta i should get wouldnt even know about the coil to use what watt to vape at. So far this and the battlestar is what im looking at maybe the limitless gold
Limitless Gold RDTA - Vapor Hub
Just want something that wont leak easy to wick and build on that dont guzzle juice atm i do about a tank a day with the baby beast at 65 w with .4 ohm
Just want something that wont leak easy to wick and build on that dont guzzle juice atm i do about a tank a day with the baby beast at 65 w with .4 ohm
Then you're better off with the Ammit 25 rta. If you need help with it on how to build let us know. It'll go nicely with the Battlestar!
- Status
Similar threads
