Another modified rba
- Thread starter redeyedancer
- Start date
- th_trl_thread_readers 0
- Status
Any chance of an igo-L on a low profile Reo? My eyes and fingers are getting too old for this teeny tiny stuff. The RM 2.0 is about my size limit anymore. Oh.... and can you put capture holes in the posts to stick the coil wires thru? 
Galaxy Note 3 via Tapatalk
Galaxy Note 3 via Tapatalk
There are capture holes... Go back to the first post... I can't do the screw capture either that's why I'm so excited data haha
that's why I'm so excited data hahaThere are capture holes... Go back to the first post... I can't do the screw capture either
Doh! Missed that - wish the the I-go-L's had them, hate wrapping wires around the tiny screws too.
Datalux, get some really strong reading glasses, like 3x or 5x, they work really well!
I'm appreciating the RM2 today after putting it away for a Cyclone
At first I determined I was getting more flavor from the Cyclone (stock cap) than the RM2
using micro coils.
Then I got an AFC cap for it and went with duals for some reason the flavor wasn't there; lots of vapor yes, but like a lot of dual coil atomizers, a lot more vapor than flavor (ymmv).
I went back to single micro w/stock cap again, and even a nano dragon build, but lol, looks like I've lost the knack for the Cyclone. wth. Tiny 1mm at most air hole too.
The RM2 has more room, nice ceramic base, juice goes back down, and comes up at the base.
Enjoying a nano dragon build, which is a little micro coil, where the cotton or hemp puff fiber is under and over the coil, leaving one side of the coil open and free to shoot the vapor out (towards the airhole).
I'm thinking the chamber is just the right size and the air hole is a little bigger than the Cyclone's.
We won't need the milled catch cup for either the stock Cyclone or the RM2, and this new modded IGO but for now i"m sticking with the RM2 . so I appreciate Commies' suggestions; something bigger for the milled Reo.
btw is there a Cyclone setup thread anywhere? I'll do a search because i have to go back to the drawing board for that one.
KUDOs to Rob for the RM2
Then I got an AFC cap for it and went with duals for some reason the flavor wasn't there; lots of vapor yes, but like a lot of dual coil atomizers, a lot more vapor than flavor (ymmv).
I went back to single micro w/stock cap again, and even a nano dragon build, but lol, looks like I've lost the knack for the Cyclone. wth. Tiny 1mm at most air hole too.
The RM2 has more room, nice ceramic base, juice goes back down, and comes up at the base.
Enjoying a nano dragon build, which is a little micro coil, where the cotton or hemp puff fiber is under and over the coil, leaving one side of the coil open and free to shoot the vapor out (towards the airhole).
I'm thinking the chamber is just the right size and the air hole is a little bigger than the Cyclone's.
We won't need the milled catch cup for either the stock Cyclone or the RM2, and this new modded IGO but for now i"m sticking with the RM2 . so I appreciate Commies' suggestions; something bigger for the milled Reo.
btw is there a Cyclone setup thread anywhere? I'll do a search because i have to go back to the drawing board for that one.
KUDOs to Rob for the RM2
For like a cyclone, How do you turn the post - by screwdriver ? Or does it push right out?
Last edited:
It's press-fit. Pliers, or (if there's a slot in the bottom) screwdriver should do it. I used to just stick a syringe needle through the wire hole and turn it.
Around $30 probably a little less . I want to mod them before I set a price
I picked a couple of the larger atomizers I need some time before I decide which one I will make available . I dont think you will get a dual coil or a larger atomizer to vape better then a smaller atomizer Easier to build maybeAny chance of an igo-L on a low profile Reo? My eyes and fingers are getting too old for this teeny tiny stuff. The RM 2.0 is about my size limit anymore. Oh.... and can you put capture holes in the posts to stick the coil wires thru?
Galaxy Note 3 via Tapatalk
I got mine to turn holding the base in a pair of robo-grips (with a protective jar opener around it) while using the correct size screwdriver. Thanks y'all
Air hole now at 12:00.
Air hole now at 12:00.
I think most everyone agrees on the dual coil thing; but we all go through that phase too. (and some folks seem to stick with it) I think it would make sense to offer a bf modded dual coil atty. It would make a bunch of people happy. The IGO-W (oops I think I've said this) has an excellent cost/quality ratio.
Hmm was planning on ordering my first Reo, and a RM2 soon, but I like the idea of an all SS RBA, any eta on availability yet?
8x glasses were too much for me… i use 3.50 at least reading glasses, and when i use the 8x, its a hell of a thing to get the right distance from the coil… like 3 to 5 inches? very awkward…
I could try another spec like 6x or 7x or even 5x but at $23 a pop…. ugh.
Theres a kit on ebay with the replaceable lens kit; many choices for less than $20.
I could try another spec like 6x or 7x or even 5x but at $23 a pop…. ugh.
Theres a kit on ebay with the replaceable lens kit; many choices for less than $20.
You need to try one of my dad's moves. Take what u wanna see to Walmart and try on the cheap reading glasses till u find a set that works... Just make sure u get men's. Dad looks funny wearing his clear frame reading glasses with pink/purple fireworks on the legs.
Sent from my HTC6500LVW using Tapatalk
Sent from my HTC6500LVW using Tapatalk
- Status
