Anybody Using A Kabuki?
- Thread starter jwbnyc
- Start date
- th_trl_thread_readers 0
- Status
I have to ask:
Are you backing the coil around until you hear the coil threads engage with the Kabuki?
I find if I don't do that, every time, I get cross theading on the 510 Kabukis.
Are you backing the coil around until you hear the coil threads engage with the Kabuki?
I find if I don't do that, every time, I get cross theading on the 510 Kabukis.
Okay, just checking, because I had a heck of a time with cross threading before I got religion on that point.
Just got my hands 2 days back on the Kabuki.
First impression: FLAWLESS!
Contrary to the slight troubles some users faced, coil fits perfect;y, no paper gap in fitting and works like a charm.
Have been trying Velvet Cloud liquids since a week (which are 100 % VG) and are low on taste.
Noticed there is a significant difference in the flavour compared to the aspire nautilus.
@Zen~ i stand by you to testify money's worth spent on your products. Thanks for the amazing product.
Cheers.
First impression: FLAWLESS!
Contrary to the slight troubles some users faced, coil fits perfect;y, no paper gap in fitting and works like a charm.
Have been trying Velvet Cloud liquids since a week (which are 100 % VG) and are low on taste.
Noticed there is a significant difference in the flavour compared to the aspire nautilus.
@Zen~ i stand by you to testify money's worth spent on your products. Thanks for the amazing product.
Cheers.
I was going to do something similar to the upgrade chimney only out of harder steel. Make it a little longer for my fat fingers to grip and at the other end add a hex bit for the air control. Drill a hole through it and put it on a key ring
I was thinking of doing the same thing, but instead of harder steel, just using the carto upgrade kit. In practice with the kabuki top cap, I found I needed "teeth" to clear the debris and excess chrome coating. I ended up using a fresh razor-blade point held sideways.I was going to do something similar to the upgrade chimney only out of harder steel. Make it a little longer for my fat fingers to grip and at the other end add a hex bit for the air control. Drill a hole through it and put it on a key ring
Sent from my iPad using Tapatalk
An issue? Not a complaint.
I have a Kabuki with the P3 fitting. I have a P3 to use with the new topper. Unless I screw in the coil as tight as I can get it (with help) and then screw the topper on, then use the hex wrench to help me tighten it a smidge tighter, it'll work.
But, if I do not follow all of these steps, no hiss at all. This is my ADV, so by this point I've ran maybe a dozen or more coils (incl ones bought from ProVape) and this is my life. I fear tightening everything so tight, but if I must, I must as I love this setup.
I do drop stuff, and to date have broken the glass twice - oh well.
Any thoughts or ideas? If it matters, I bought this from the first batch on ProVape.
I have a Kabuki with the P3 fitting. I have a P3 to use with the new topper. Unless I screw in the coil as tight as I can get it (with help) and then screw the topper on, then use the hex wrench to help me tighten it a smidge tighter, it'll work.
But, if I do not follow all of these steps, no hiss at all. This is my ADV, so by this point I've ran maybe a dozen or more coils (incl ones bought from ProVape) and this is my life. I fear tightening everything so tight, but if I must, I must as I love this setup.
I do drop stuff, and to date have broken the glass twice - oh well.
Any thoughts or ideas? If it matters, I bought this from the first batch on ProVape.
Well, there have been a few P3 devices that have the positive pin set a little low, and when this condition exists it won't make contact, the solution is to give me a call at the shop (house of hybrids) on Monday when I get back from vapercon in Richmond, and I'll send you a P3 Kabuki base that has the coil seat machined about .02 lower and that will insure that it makes connection every time.
It is a rare, but known problem that I am happy to fix for you.
VaporWerk coils update: I think I said I put the 2.2 VW coils in my Kabukis. Worked fine. However, last night after only maybe half a tank one of the coils just stopped working. No error message from the P3. It was firing OK. Just no vapor. I pulled it out, couldn't see anything wrong with it and replaced with a stock Aspire coil. Wow, what a taste difference! I don't know why I didn't notice it the first time. Bad taste buds from smoking forever, I guess. Anyway, I pitched the VW coils and went back to the Aspire coils. Save your money.
I thought of that, but then I fear always having to open it up to see how much juice I have left. It would bug me badly I think.
Thank you Sir, you are very kind, and I will give you a call this coming Monday
I love the tank, and I never 'build' anything, so it is right up my alley! Plus the flavor puts my other toppers to shame, so I refuse to use them. But that means I have no 'spare' either...
Good to know Juma!
I have ditched all my other tanks in favor of the Kabuki....it really is a super nice tank (thanks for the excellent work Zen )....so I stocked up on Nauti coils big time!!...than I saw these new coils and wondered.......so the feedback is appreciated!
I have ditched all my other tanks in favor of the Kabuki....it really is a super nice tank (thanks for the excellent work Zen
)....so I stocked up on Nauti coils big time!!...than I saw these new coils and wondered.......so the feedback is appreciated!- Status
Similar threads
- Locked
