Anybody Using A Kabuki?
- Thread starter jwbnyc
- Start date
- th_trl_thread_readers 0
- Status
Replacement o-rings and tanks are available at: https://thezfo.com located in the US. You may want to contact them first as it relates to shipping to Mexico — zenfactoryoutlet@gmail.com
About the highest VG I have tried in the Nautilus coils is 60%. They are not designed for high VG eliquids so even 60% can be pushing it.
If you like the 1.6Ω @ 10watts and it's not burning, then go for it. I usually use Kabuki's and Nautilus coils at around 8-11watts with no problems. I have vaped MaxVG juices using nautilus + Kabuki and it works fine, but you get maybe 2 or 3 tanks out of a coil before it's toast; using high PG thinner juices like Halo and the lifespan of 1 coil turns into 20-30 tanks for me. Whatever you try, the worst thing that can happen is it'll gunk up the coil faster and make you replace it sooner; it's not going to somehow ruin the Kabuki.
If you are running high VG, it can be thinned with a couple drops of distilled water to help with wicking, being in Mexico, the temps may be enough to keep your juice wicking well.
Have to add my 2cents. The Kabuki works best with 70pg/30 Vg. This had been Provape and Zens recommendation. I use this ratio and can get more than a month on my 1.8ohm coils. Usually in the 7watt range. Gives me good flavor, not too hot, good but not excessive vapor. I use these guidelines with the Kabuki, Z Attys, Kay fun 5s and even a couple Aspires.
IndeedKahlua can keep one well-wicked as well.
, but if you ask me Tequila will be more efficient.
Enaud, when you mentioned 3 drops of water, that is enough for the 3.5 mls the Kabuki can hold?
I downgraded to 60vg/40pg in one Kabuki and 50/50 in the other one. Every thing goes fine !!
Enviado desde mi iPhone utilizando Tapatalk
Good to hear it's going fine. If you need to run the higher VG, and if you have wicking issues, yes, a couple drops of water per tank will thin juice down. If your not getting any dry hits then I wouldn't worry about it.
Let me be the first...
These ProVape Forums, are and have been paid for by ProVape.
I see them closing at some time in the future, and would like to say that:
I have enjoyed being here with Y'ALL!!!
My PM will be open, and I will continue here as long as they will have us.
Your Naughty Provi Brother, Jim
These ProVape Forums, are and have been paid for by ProVape.
I see them closing at some time in the future, and would like to say that:
I have enjoyed being here with Y'ALL!!!
My PM will be open, and I will continue here as long as they will have us.
Your Naughty Provi Brother, Jim
Seasonal Affective Disorder.
Having said that, Turfyness, thank you. I, too, have enjoyed our Proyears together VERY much.
Having said that, Turfyness, thank you. I, too, have enjoyed our Proyears together VERY much.
Losing love for my Kabuki's
A late Happy New Year to all.
I'm looking for some help with the P3 to 510 adapter. I have three Kabuki P3 tanks and two adaptors, one of which I have never been able to get to work.
The one that will work on a 510 mod only works with my titanium kabuki. The stainless and gunmetal Kabuki's will not conect and I get error messages on the mod which is not Provari.
All tanks work fine on the 2 Provari P3, I have tried a number of coils, no joy. I've also used the same coil that works on the Ti with the adapter on the other tanks but no luck.
I'm guessing that the ss and gunmetal tanks are longer in the bottom thread section, so was thinking of trying to file it down a v little in the hope of a contact but concerned about distorting the thread.
Any help would be much appreciated, I'm in the UK so not easy to get much done with the House of Hybrids.
All the best for 2017. Cheers
A late Happy New Year to all.
I'm looking for some help with the P3 to 510 adapter. I have three Kabuki P3 tanks and two adaptors, one of which I have never been able to get to work.
The one that will work on a 510 mod only works with my titanium kabuki. The stainless and gunmetal Kabuki's will not conect and I get error messages on the mod which is not Provari.
All tanks work fine on the 2 Provari P3, I have tried a number of coils, no joy. I've also used the same coil that works on the Ti with the adapter on the other tanks but no luck.
I'm guessing that the ss and gunmetal tanks are longer in the bottom thread section, so was thinking of trying to file it down a v little in the hope of a contact but concerned about distorting the thread.
Any help would be much appreciated, I'm in the UK so not easy to get much done with the House of Hybrids.
All the best for 2017. Cheers
If you are handy, you may be able to replace the center pin of the adaptor with a slightly longer pin. Hobby stores sometimes have a little display of brass and steel pin stock or maybe they will call them metal rods. I replaced one of mine in this fashion. Also a very large company in China sells spare 510 bases for the clone. That are only a few bucks. Good luck.
Many thanks Enaud. I will check out a 510 replacement base, wish H of H sold them
I think I have one duff P3 to 510 adapter which I might be able to fix and one that works fine with the titanium kabuki but not the othe 2 Kabuki's. This makes no sense to me which is why I think the fault is with the base of the ss and gun metal Kabuki's as they should work on the adapter that is ok.
Anyone else had this issue?
Cheers. Sean
Last edited:
- Status
Similar threads
- Locked
