I got some really good advice last time from people here it saved me lots of money. So thanks for that and I want to pick your brains some more. I really new at this (less than 6 months) got a twist. Just ordered a pheonix rba and ss mesh prerolled wicks. Going for a dual coil vert ss wicked. What ohm should each coil be for use with a twist. And I'm looking to step up to a apv thinking the new zmax coming out. Will this set up work out? is it possible? still amazed what a great resource the site is. Thanks
Apv to go with dc ss pheonix rba
- Thread starter All Day Nic Fit
- Start date
- th_trl_thread_readers 0
- Status
If you use two 3ohm coils in parallel then the resistance will be 1.5ohms
If you use two 4ohm coils in parallel then the resistance will be 2ohms
You see the pattern, each coil has to be double the desired resistance
I'm not sure how suitable the Twist is for powering dual coil atomizers
Maybe someone with Twist experience can help you more than I can
I'm good for a bump anyway
BTW - I have a couple Phoenix Atomizers on the way from Vapor.....
If you use two 4ohm coils in parallel then the resistance will be 2ohms
You see the pattern, each coil has to be double the desired resistance
I'm not sure how suitable the Twist is for powering dual coil atomizers
Maybe someone with Twist experience can help you more than I can
I'm good for a bump anyway
BTW - I have a couple Phoenix Atomizers on the way from Vapor.....
Last edited:
Twist only has an amp limit of around 2.5amps... You need something with at least 3.5 amps, preferably more. Most mechanical mods with high drain batteries, Provari, Saber Touch, whats that other one people love... kinda like a Provari but no screen and has a wheel for voltage adjustment...
Anywho you get the idea... None of the eGo's or smaller things like that are gonna do it, at least not well.
Anywho you get the idea... None of the eGo's or smaller things like that are gonna do it, at least not well.
I'm pretty sure that the vertical coils with SS wicks is going to be an extremely tight fit
I've seen pictures of the vertical single coil with SS wick and can't imagine fitting two
Not much room inside the Phoenix
I've seen pictures of the vertical single coil with SS wick and can't imagine fitting two
Not much room inside the Phoenix
I will have to start with one coil then. I thought the amps would get in the way. Is vw a more stable temp than vv? Or is it just the lack of having to use ohms law?
VW takes the math out of your hands. You set the wattage to what feels good, and then forget about it.
I have zero dual coil xp would a passthrough power a dc atty? How many amps does it need?
Try mastering the single coil before attempting a dual coil
There is a learning curve with building coils
There is a learning curve with building coils
One coil it is. Can't wait to try this! I love to tinker and have made a goal of mastering atty mods. (Master in my own mind anyways). Any other advice would be great.
BTW, where did you find prerolled SS Mesh wicks? Mind that pre-rolled or not, SS Mesh wicks can tend to be a bit fidgety till they have some use on them.
I got a phoenix on the way as well just make sure to test your coils before putting on the twist i heard shorts will fry your battery quick......
VW, what's that?
And for taking the math out of your hands...
Are you talking about just dialing in a Specific wattage you want to be at and you just leave the device to figure it out from there?
I thought that is what the New Provari is suppose to do; am I wrong or making stuff up in my noodle noggin' again?
Thanks
Glad you asked...
That would be from Vapor......com
They also sell T-Shirts
Stainless Steel 400 Replacement Wick and Wire for Rebuildable Atomizers
Last edited:
Is that thing ready to cut and roll with it?
Carbonized, is that the word I'm looking for? After you roll it then you put some eJuice on the wick and you burn the juice with a lighter to put some carbon all over the bare metal bits? Like the Video Mr. Bonner does make!
Carbonized, is that the word I'm looking for? After you roll it then you put some eJuice on the wick and you burn the juice with a lighter to put some carbon all over the bare metal bits? Like the Video Mr. Bonner does make!
Last edited:
I'll be getting some probably tomorrow
But I doubt that it has been fully prepped
Just rolled
Maybe the word is OXIDIZING it, using a torch and water
As shown in this tutorial
Reinventing the Phoenix Rebuildable Atomizer « pinoyvaper
But I doubt that it has been fully prepped
Just rolled
Maybe the word is OXIDIZING it, using a torch and water
As shown in this tutorial
Reinventing the Phoenix Rebuildable Atomizer « pinoyvaper
Last edited:
The Provari is Variable Voltage. You set the voltage based on the resistance of the "heater" you are using. Variable Wattage is what the Darwin and a few others do. You set the wattage you want, and don't worry about the resistance or any of that.
Just judging by the picture... It might be slightly seasoned, but not much. It would definitely need to be seasoned more to make a GOOD wick.
- Status
Similar threads
