Star - I was just kidding ... that was, and still is my first and favorite tubular, and it's TALL!!
oh i didn't know it was your first always got to keep your first
Art Glass Drip Tips
- Thread starter bert1983
- Start date
- th_trl_thread_readers 0
- Status
oh i didn't know it was your first always got to keep your first
Not my 1st Trippy, but the 1st tall narrow one I got that started the preference.
Boy, step away for a minute to put our DD to bed and the thread blows up.
Hi Bert, Goodnight Bert.
I blame Blu for my new affinity to the classies and my obsession for brass and just my PV addiction in general. The rash formed weeks ago and now I know what it is.
Funny thing is we never argue.
I don't think sashwa could have gone over voltage. The highest the VVW goes is 5.5 and on a 2.5 ohm, that should be fine. And it seems like she started it off with the right amount of juice.
Makes for great creativity.
Hi Bert, Goodnight Bert.
I blame Blu for my new affinity to the classies and my obsession for brass and just my PV addiction in general. The rash formed weeks ago and now I know what it is.
Funny thing is we never argue.
I don't think sashwa could have gone over voltage. The highest the VVW goes is 5.5 and on a 2.5 ohm, that should be fine. And it seems like she started it off with the right amount of juice.
Makes for great creativity.
Not my 1st Trippy, but the 1st tall narrow one I got that started the preference.
oooooo i understand now lol
goodnight sleep well sooner
High Tripsters
Use a Donut on the 357's and its a lot easier with no spitting and you can over squank and run them plenty wet enough with no problems, any extra juice comes up into the bottom of the Donut then drips back down into the Atty. Keep them wet, I run my 1.5ohm 357's anywhere from 3.5-4.2v depending on the juice with the Donuts and they work great.
Use a Donut on the 357's and its a lot easier with no spitting and you can over squank and run them plenty wet enough with no problems, any extra juice comes up into the bottom of the Donut then drips back down into the Atty. Keep them wet, I run my 1.5ohm 357's anywhere from 3.5-4.2v depending on the juice with the Donuts and they work great.
Matt. Sashwa is having trouble. She says it draws fine when dripping, but when squonking she is not getting juice up into the atty and it is hard to draw.
Is sashwa using a Reo Grand ? or a different feeder ? if a Reo there shouldnt be any issues at all with the bottom feeding and a 357 or any Atty, accept for one, and that's if her hose in the bottle is sitting flat on the bottom of the bottle, tell her to make sure it is cut on an angle and not sitting down tight on the bottom, if this is happening it wont squank properly.
You can see in my Avatar I have what 5 there, all have 357's on them and a Donut, all kick Azz and vape super.
You can see in my Avatar I have what 5 there, all have 357's on them and a Donut, all kick Azz and vape super.
Last edited:
Matthew - I think she already checked that ... the problem she is having sounds like the bottom of the atty is closed/clogged/something .... she says it's a VERY tight draw. Other atties on same Reo are fine.
Matt. What Blu said. She is using a VV Woodvil. We did talk about cutting the tube at an angle. She is sending it to me to see if I can figure it out. In the mean time, I am presently breaking in a new one for her.......blah.................
I know the 357 intimately let say there is nothing on the bottom of it to block the juice flow or the internals, take off the Atty and blow through the bottom hole, if juice blows out which it will the Atty is fine, there is jut nothing stopping the juice or shouldn't be unless something got into the bottom hole to block the feed from happening. Blow out Atty put back on, squank and vape
there is nothing on the bottom of it to block the juice flow or the internals, take off the Atty and blow through the bottom hole, if juice blows out which it will the Atty is fine, there is jut nothing stopping the juice or shouldn't be unless something got into the bottom hole to block the feed from happening. Blow out Atty put back on, squank and vape
I just did up my RBA Bulli smoker Atty with a small amount of the special mesh wool used in the 357 and man oh man is it kicking some bootay loving all these RBA Atty's that are coming out, also that new Smok Tank looks super that is coming out, the Z-Atty, the DID, man so many dam great Attys and good stuff is coming and even more so that hasnt been seen as of yet, it just keeps getting better and better.
loving all these RBA Atty's that are coming out, also that new Smok Tank looks super that is coming out, the Z-Atty, the DID, man so many dam great Attys and good stuff is coming and even more so that hasnt been seen as of yet, it just keeps getting better and better.
Matthew - I am waiting for something cool to come out soon also .... well, a couple somethings. LOL
Hopefully in the next month.
Hopefully in the next month.
Same to you Starlight682, it was a wonderful weekend thanks,,,,,,,,,,,,,,,,,,,,ya blue lots of great stuff coming,,,, I got in on a CoOp for the new Smok tanks, another for the Fatty v2 Atty, the ERA Atty which should be super for the Reo's or any bottom feeder seeing its a bottom fed RBA, and that's just the start of it,,,,,,,, then we have Mods like the Lexi that mamu is making , that Nivel chip is amazing,,, the newer DNA Chips are super, just a lot of great stuff and so much more on the way.
- Status
Similar threads
