Aspire triton
- Thread starter carly cat
- Start date
- th_trl_thread_readers 0
- Status
Yeah, luckily I had read all about the on/off switch issue before I got the tank. I've filled up the tank 4 times now since I got it and it hasn't leaked a single drop of juice.
how about I vape on it some and take a picture when I have an opportunity... I am pretty certain you know what one looks like as Aspire's advocate...
Just got my Triton today. A little rough start, but my bad, I primed my coil too much. After taking it out and blowing out the excess juice, it's fine. I also am turning it to fill if I let it sit, just in case. Really liking it so far.
I just noticed...he copyrighted the picture................. 
so noone counterfeits the pictures... i can dig it... can't trust those dang counterfeitersI just noticed...he copyrighted the picture.................
Aspire USA apparently told distributors that the Atlantis II coils will also work in the Triton.
I had some Atlantis II .3 Ohm coils, so I put one in. Didn't take long before I started to get leakage into the bottom air chamber. Took about two seconds to figure out the coil doesn't seat properly.
I compare that coil to a Triton .4 and notice they are not the same. They isn't a huge differences, but even a little difference is an issue.
I call up UVApe (Aspire USA) and I tell him the issue. We talk for a few minutes and stumbled on the issue.
A few months ago Aspire released a new Atlantis II Coil with organic cotton to replace the current one that had a ceramic insulator. They never brought up the design.
I then picked up the organic cotton coils and what do you know......identical to the Triton coil.
Now I'm chugging away on 80w.
I've seen so many posts about Aspire coils not heating evenly, bad cotton, and lots of other issues.
Authentic Aspire coils don't have those issues.
They only sell coils in 5-packs and and should cost $20-23.
Aspire doesn't sell 15-packs.
And you won't find a 5-pack for $12.25
FYI: UVape is now accepting pre-orders for the Triton Ni coils.
Note: If you are buying Authentic Aspire products from a US retail store or online site, make sure you can follow it back to UVape.
If there are Ni coils before
I had some Atlantis II .3 Ohm coils, so I put one in. Didn't take long before I started to get leakage into the bottom air chamber. Took about two seconds to figure out the coil doesn't seat properly.
I compare that coil to a Triton .4 and notice they are not the same. They isn't a huge differences, but even a little difference is an issue.
I call up UVApe (Aspire USA) and I tell him the issue. We talk for a few minutes and stumbled on the issue.
A few months ago Aspire released a new Atlantis II Coil with organic cotton to replace the current one that had a ceramic insulator. They never brought up the design.
I then picked up the organic cotton coils and what do you know......identical to the Triton coil.
Now I'm chugging away on 80w.
I've seen so many posts about Aspire coils not heating evenly, bad cotton, and lots of other issues.
Authentic Aspire coils don't have those issues.
They only sell coils in 5-packs and and should cost $20-23.
Aspire doesn't sell 15-packs.
And you won't find a 5-pack for $12.25
FYI: UVape is now accepting pre-orders for the Triton Ni coils.
Note: If you are buying Authentic Aspire products from a US retail store or online site, make sure you can follow it back to UVape.
If there are Ni coils before
This thread is confusing... I have had a few leak issues with my triton because of my own stupidity... over filling the tank mainly.... I never fill it completely now, and the issue has resolved itself... It is easy to flood the coils because of the top fill design and how the tank forces the juice into the atty once its switched back to vape mode....
I prime my new coil slightly...
make sure base and tunnel are clean
screw in coil... attach to tank...
Fill tank 3/4 full....
I start on my IPV 3Li at about 20w for the first couple hours...then slowly move up...
I find that flavor is best around 40-45w once the coil is broken in...
I find that most sub tanks spit every now and again.... I also had the Delta II and i still have a Arctic as well....
IMO the triton is a great tank... I love mine...
I prime my new coil slightly...
make sure base and tunnel are clean
screw in coil... attach to tank...
Fill tank 3/4 full....
I start on my IPV 3Li at about 20w for the first couple hours...then slowly move up...
I find that flavor is best around 40-45w once the coil is broken in...
I find that most sub tanks spit every now and again.... I also had the Delta II and i still have a Arctic as well....
IMO the triton is a great tank... I love mine...
I've had the same issue. As others have said it's probably a bit flooded, not so that it doesn't work but just has excess juice. You can try opening up the bottom airflow, that will pull less juice in. That has helped it for me. And getting a longer mouthpiece helps.
Another member posted this in a different thread.
https://www.fasttech.com/products/3016/10017703/3629408
Could be something to try to block the splatter.
---
Hmm... the link was blocked. Assuming it's my user status.
Go to fasttech.com
search for
POM + Stainless Steel Hybrid 510 Drip Tip
There is a mesh screen in the drip tip
https://www.fasttech.com/products/3016/10017703/3629408
Could be something to try to block the splatter.
---
Hmm... the link was blocked. Assuming it's my user status.
Go to fasttech.com
search for
POM + Stainless Steel Hybrid 510 Drip Tip
There is a mesh screen in the drip tip
I gave up on this tank. It started leaking from the top fill and is so messy now. Plus it's a pain to clean.... I just bought the uwell crown tank. It's so much better than the triton...easy top fill by just unscrewing the top(no switching to modes) you can vape at a higher wattage and no leaking... im sold.
- Status
Similar threads
- Locked
