Atmistique Atomizers

[nelsonm64]

I hope it moves westwards on Monday... I'm praying for it.
My GR-Modders package is also in Montreal (Customs) since the last 2 days

I suspect it's already half way here despite it saying it's still in Ontario. tracking is slow this holiday season! things have just been showing despite what tracking says... can't wait to try the V2... and compare it

 

[Kataphraktos]

Kat and how about the quest of the holy e-juice? )))

There are many juices that may be used in the Sacrament. I just finally gave in and ordered a sampler of the very expensive five pawns. They should work well in thwarting Satan. Or a rabid bunny with fangs.

 

[Firestorm]

I received my second Enezlis on Friday. I was hoping they DHL would deliver my Paps X on the same day, but no updates since Thursday.

 

[newvap4me]

Hi Everybody,
Any tips you can give me with wicking issues on my diver. vaping at 1.5 ohms, using the diver in a Ibtanked.
2 pieces of 1 inch ekowool.

Thanks

 

[raqball]

Diver V1 or V2?

Dry hits or gurgling?

 

[newvap4me]

Hi raqball, diver v1 dry hits. If draw it a little then take a vape it works okay.

Diver V1 or V2?

Dry hits or gurgling?

 

[raqball]

Here are a few things to try:

1) Only fill the tank to about 70%
2) Make sure the wick ends are not to long. If the wick ends touch the threading on the base, they are to long
3) The juice hole should be centered between the wick ends / legs.

Like this: ==O== (== is wick legs and O is the juice hole)

4) Make sure the wire is not wrapped to tightly around the wick.

Check / try that and report back..

 

[newvap4me]

Thanks Raqball I don't have the wick legs centered between the juice hole. I will check that and report back, when I get to trying that, probably tomorrow. Thanks for responding to me again. Any idea where I can get a v2. I chekced on atmistique site and they don't have stock now.

Here are a few things to try:

1) Only fill the tank to about 70%
2) Make sure the wick ends are not to long. If the wick ends touch the threading on the base, they are to long
3) The juice hole should be centered between the wick ends / legs.

Like this: ==O== (== is wick legs and O is the juice hole)

4) Make sure the wire is not wrapped to tightly around the wick.

Check / try that and report back..

 

[raqball]

Bingo!

The juice hole not being centered would be the culprit then.

Tip: Screw down the tube before you put the ceramic in. Make a mark with something like a sharpie on the base that lines up with the juice hole. Unscrew the tube and put the ceramic in the base with the wick ends going to the left and to the right of the mark you just made,

Now when you screw the tube back on the juice hole should be centered between the wick ends.

Hope that made sense.

Re: Diver V2. Atmistique is the only place to get one at the moment I believe. Maybe K will be along soon to update when more will be made.

 

[newvap4me]

Thanks raqball, once again you have helped me out. Hopefully I will be able to enjoy my diver on my paps piccolo a lot more. Can't wait to try it.

Bingo!

The juice hole not being centered would be the culprit then.

Tip: Screw down the tube before you put the ceramic in. Make a mark with something like a sharpie on the base that lines up with the juice hole. Unscrew the tube and put the ceramic in the base with the wick ends going to the left and to the right of the mark you just made,

Now when you screw the tube back on the juice hole should be centered between the wick ends.

Hope that made sense.

Re: Diver V2. Atmistique is the only place to get one at the moment I believe. Maybe K will be along soon to update when more will be made.

 

[raqball]

No problem.. Make sure to rub the sharpie mark off before you put it in the tank

Enjoy

 

[Konstantinos]

Good afternoon

Nelson-Firestorm all the PO of the world are faithful to the tradition of, the days before and after Christmas to relatively slow.

finagle69 I have already see this movie many times but I can see again as many, unique! On the other hand I think Kat must see or better read “Das Parfum”

newvap4me pls check also the below pic:

 

[Konstantinos]

Next Tuesday 16.00 GMT some Divers with flange will be available again.
Most likely flangless Divers and 45mm tubes will be available again early January.

http://www.atmistique.gr/en/craven-...page_images.tpl&product_id=480&category_id=75

 

[Kataphraktos]

Good afternoon

Nelson-Firestorm all the PO of the world are faithful to the tradition of, the days before and after Christmas to relatively slow.

finagle69 I have already see this movie many times but I can see again as many, unique! On the other hand I think Kat must see or better read “Das Parfum”

newvap4me pls check also the below pic:
View attachment 283509

I have! I've also not only studied perfume making, I even dabbled in it at home for a while after I saw that movie. The scents I made were... interesting, though nothing most people would want to wear, I suspect.

 

[Konstantinos]

It must be very interesting, you make me jealous now

 

[tj98_7]

Can u just buy a 4 mm tube or does it only come in a complete unit?

Sent from my SAMSUNG-SGH-I337 using Tapatalk

 

[tj98_7]

45mm

Sent from my SAMSUNG-SGH-I337 using Tapatalk

 

[Konstantinos]

From the new year all the Divers tubes can be sold separately

 

[newvap4me]

Its working great now, thanks for the advice.

Thanks raqball, once again you have helped me out. Hopefully I will be able to enjoy my diver on my paps piccolo a lot more. Can't wait to try it.

 

[newvap4me]

Thanks for the diagram. I wish you were getting the flangeless ones, I still need another diver for my SnP tank. I guess I need to be patient.

Good afternoon

Nelson-Firestorm all the PO of the world are faithful to the tradition of, the days before and after Christmas to relatively slow.

finagle69 I have already see this movie many times but I can see again as many, unique! On the other hand I think Kat must see or better read “Das Parfum”

newvap4me pls check also the below pic:
View attachment 283509