A little bit of both, let's just blame all of Europe to be safe!
Atmistique Atomizers
- Thread starter billakosgr
- Start date
- th_trl_thread_readers 0
- Status
A little bit of both, let's just blame all of Europe to be safe!
As I think I've mentioned on this thread before, I used to work for a Franco-Italian company...it was not uncommon to see this in someone's office in Italy.
Heaven is where the...
Cooks are French,
Mechanics are German,
Police are British,
Lovers are Italian,
And it's all organized by the Swiss
Hell is where the...
Cooks are British,
Mechanics are French,
Police are German,
Lovers are Swiss,
And it's all organized by the Italians
Sent from my iPad
Heaven is where the...
Cooks are French,
Mechanics are German,
Police are British,
Lovers are Italian,
And it's all organized by the Swiss
Hell is where the...
Cooks are British,
Mechanics are French,
Police are German,
Lovers are Swiss,
And it's all organized by the Italians
Sent from my iPad
As K said earlier, yes, they are doing another run right now, should be up in a week or so.
Billet Box with Diver v2 using the v1 pin:
Three full tanks, zero leaks, floods or other issues. I had to re-wick once halfway through tank #3, the cotton was toast. When I pulled the tank out, there was a bit of juice on the back of the tank - as Dayloon mentioned above - but I would not have noticed this if I had not pulled out the tank. The BB does this with cartos as well, and it did not have any effect on vape quality or experience. The juice was only on the rear of the tank, the 510 connector area was almost completely dry, just some condensation, as always.
This is now 3 tanks over the weekend, both at home and out and about.
I will continue using with the v1 pin permanently, but I'd like to hear feedback from others using the v1 pin to confirm my results.
Three full tanks, zero leaks, floods or other issues. I had to re-wick once halfway through tank #3, the cotton was toast. When I pulled the tank out, there was a bit of juice on the back of the tank - as Dayloon mentioned above - but I would not have noticed this if I had not pulled out the tank. The BB does this with cartos as well, and it did not have any effect on vape quality or experience. The juice was only on the rear of the tank, the 510 connector area was almost completely dry, just some condensation, as always.
This is now 3 tanks over the weekend, both at home and out and about.
I will continue using with the v1 pin permanently, but I'd like to hear feedback from others using the v1 pin to confirm my results.
I'm having exactly the same results. No problems at all since using the v1 pin in the v2 diver for my billet box. It's a fantastic vape. The juice at the back isn't causing any issues, it's only a bit and I just wanted to make sure it was normal.
Sent from my iPhone using Tapatalk
All v1 pins are brass. There are two deep grooves in the base, in a cross shape.
The v2 pins can be SS or brass (I think SS is the default when you add to the shopping cart at Atmistique). The v2 has a single, much shallower, wider groove in the base.
Great!
We'll know what is normal when more people have run their setup with the v1 pin. One just left for Texas. but we have two data points showing this to be the case. I don't like to speak too soon and say "Fixed" until we really have tested this, both for length of time and widespread experience from many more users.
If this does turn out to be normal behavior, I would say it is working properly. That tank has to come out every 3 tankfuls so the cotton can be replaced regardless, wiping down a bit of juice from the back of the tank is just 5 seconds of extra work, and no different than unscrewing any other tank from a conventional tube mod to clean out the 510 and get rid of the same excess juice from the collector well.
Akdare: do you use joined wires or just res wire?
kimochi-ii: Divers are already in production. We try to make a lot of pcs and for all parts of it. I hope beginning of next week we will be ready.
BB: i dont keep my promise because i forget that we send the BB brass ring for golden plated
I hope tomorrow we will have them. I dont know what to say i vape with ss pin without a problem . Anyway if the V1 is better for some i will ask to make more V1 pins. Hopefully we are in production now
kimochi-ii: Divers are already in production. We try to make a lot of pcs and for all parts of it. I hope beginning of next week we will be ready.
BB: i dont keep my promise because i forget that we send the BB brass ring for golden plated
I hope tomorrow we will have them. I dont know what to say i vape with ss pin without a problem . Anyway if the V1 is better for some i will ask to make more V1 pins. Hopefully we are in production now
BB: i dont keep my promise because i forget that we send the BB brass ring for golden plated
Fancy Greeks! This gold plating thing could get fiscally dangerous.
Update: v1 all o-rings (packs of 2mmx1.5mm for the v1 pin and 6mmx1mm for the upper base) left today via USPS, kindly PM me when they are received and please inform me if they change you Diver v1 performance. So far, most recipients who have gotten them have written to say the o-ring fix has solved the leaks completely.
I urge anyone with a V1 to do this upgrade. Not a single leak from the bottom at all.
Akdare: do you use joined wires or just res wire?
kimochi-ii: Divers are already in production. We try to make a lot of pcs and for all parts of it. I hope beginning of next week we will be ready.
BB: i dont keep my promise because i forget that we send the BB brass ring for golden plated
K, I use joined wires, 30g R, 32g NR. Zapped myself. 1/16, 2.5 ohm (BB friendly). My tests were on my Provari @ 4.5v in a scuba tank.
Sent from my iPad
- Status
Similar threads
- Locked
