Attack of the Hana Modz Clone. Let's wait together!
- Thread starter Fathomrock
- Start date
- th_trl_thread_readers 0
- Status
You would think so but not everybody used rebuildables...
If I do a video it will be with an open russian 91 and an igo m. Both are rebuildable and can touch to the posts. I can do on both the clone and a panzer mech clone. it would just be an actual meeter instead of an inline on elev8s video. I can also see if the igo m has trouble making contact with the 510 pin like someone asked earlier.
Sent from my SCH-I545 using Tapatalk
My personal opinion on them.... Yes they can assist in mixing greatly. But as far as aging the liquid to allow the flavors of a complex mixture to marry and balance, not so much...
Great...... so the ohm's value of each will be the same or different?
Hope you have enjoyed the showI will be vaping my clone at crystal cove and then shopping at the fashion Island
Haha nice bro!!
Be sure to account for the resistance of the probes as well
I havent really gotten in to complex flavors yet. Thinking about doing a TPA smores in the future, but eveything so far has been single flavors for me.
Sent from my SCH-I545 using Tapatalk
My new found favorite is TFA Key Lime at 10%, it's my current ADV
Right now the russian is about 1.4 ohms. The igo ill prob set between .5 and .8
Someone stated earlier that it will give short protection if it reads under .3 but I dont want to be the first one to test that on something im so excited about lol
Sent from my SCH-I545 using Tapatalk
Tpa has great customer service too. Is that the DIY vendor you were refering to earlier?
Sent from my SCH-I545 using Tapatalk
No. BullCityVapor. He carries, TFA, FW, Cap, and Inawera right now. New kid on the block like Elev8. Crazy low prices too. Check him out bullcityvapor.com 6ml samples are like $1.30.
I've been doing DIY for about 2 years now! Have not purchased a single bottle of juice from a vendor since. I almost exclusively use TFA flavors.
Samrezies. Although Inawera is good too, still experimenting with it though I just got it in. My main reason is FW is far less concentrated.
Yep..... you should be fine at .5/.8.... that variance in values between the sub-ohm coil and the 1.4 ohm can give some idea as to how the regulation of the chip is working.... ohm's reading, voltage reading and wattage reading for each while firing would be great info...
And as an off-topic note.... sometimes the real dna chip can get confused internally (don't really know why and it very seldom happens) and the ohm's reading will lock in and no longer change. Over a year and a half I have seen it twice and only on 2 of the 10 dna's I've built. If the china dna is just like the real one this could happened with it also.... It can be easily resolved by just taking out the battery and putting it back in...then the ohm readout will function properly again....kinda like re-booting a computer...
Man! I save sooo much money on juice from DIY! It's also super easy! I don't know why some folks are so intimidated by it.
Not to mention, I've made more juice I like then juice I've bought premixed. I can make 100ml for less than some 15ml I bought. It's stupid easy. Just takes some experimenting or a recipe. Between DIY and and rebuilding all my coils I'm spending so much less, my biggest cost is by far all the new toys and batteries.
Thats very odd. I would think the chip should basically be designed to read the resistance and the current wattage setting, then run some assembly language operations to calculate the voltage for the desired output. Sometimes slots can get switched in memory allocation if certain conditions are met that weren't tested for. Especially if this thing is going into sleep mode all the time. Perhaps a sleep followed by a rapid wake could cause that.
Sent from my SCH-I545 using Tapatalk
I suspect some people are just ignorant to the fact it can be done, and others are scared because it is a bit of chemistry. You have to understand how to calculate a whole solution with solute and solvent. also working with the nicotine can be dangerous if you dont know what you are doing. If someone were to put 5mL of 100mg nic into a 10mL soultion... that would be bad. And that is probably why we hear about some ppl going to the hospital. Some of my friends I would recommend doing DIY and some I would not.
Either way. Vaping at less than $0.05 a mL is A-OK in my book
Edit: when I say ignorant, I dont mean that in an offensive way, I just mean they are not aware of it.
Last edited:
that's possible but the 2 times it happened it was not in sleep mode or coming out of sleep...it occured while normal vaping and just changed atty's and the new atty was read improperly ( or better term may be " not displayed properly") It would stay that way until power was removed and the chip resets....odd but so unusual as to not really be an issue....If peeps don't know about this they think the chip is defective or fixing to catch fire, etc, etc, etc...just wanted to post this as a public service announcement..he-he...
- Status
