Just got my first ever rda!! Authentic Patriot with a .5 ohm build (local B&M worker showed me how to wrap them). So amazed by the flavor and the copious amounts of vapor!!
Attack of the Hana Modz Clone. Let's wait together!
- Thread starter Fathomrock
- Start date
- th_trl_thread_readers 0
- Status
It looks like you guys are right, the V3 on the real ones from the pics I have looked at, does not have the spaced out V 3. It is right together on the real ones like V3. That is easiest way to tell difference between them. I found a post that looks like someone was most likely sold a fake earlier in the month when someone probably got ahold of an early one somehow unless this was real and I am wrong about the V3 part and red see through part:
For Sale: CA FS: HANA MODZ V3 (BLK REG) + KF LITE PLUS v2
For Sale: CA FS: HANA MODZ V3 (BLK REG) + KF LITE PLUS v2
Yep.... I saw that too and did a bit of checking..... the early version of the real Hana V3 had the V3 with a space and had no hole beside the usb port... saw this in a couple video's made in February of the Hana V3.. so it just muddy's the water a bit...
My understanding is that the instruction sheet is just a "clone" of the Hana instructions. So that 90 day warranty probably isn't worth anything- who's going to honor it? Just my thought...
Meh, I do that with my mechs but honestly life cycle I am not too concerned with because of how cheap these battery's are. If I only get 300/500 recharges then I am cool. I just am more concerned if it was a safety issue. I was looking into getting this new nitecore charger here:
http://www.batteryjunction.com/nitecore-d2-digicharger.html
It goes for $30 anywhere else but seems to be a little cheaper from this site. I have never had an issue with my I2 so I don't know if its really necessary. It always charges my batterys to a 4.20 exactly, sometimes 4.19... But ya, on my mechs I only let them discharge from 4.2 to 3.7 then I recharge. Honestly not because I am worried so much about life cycle but more about safety and with sub ohming on them I feel the drop off really bad if I got lower then 3.7. But if my hana charging my batteries to 4.22 is safe then I am not too worried. So from what I understand that is not a issue. This same battery does only charge to 4.2 in my nitecore charger. So I doubt its a bad battery. Plus on sx350 I can tell it doesn't have any bad sag going on or anything under load.
I am not sure about 90 day warranty but I know of at least 1 person that contacted cloupor when they had an issue and cloupor sent them another clone free of charge and last I had heard they didn't want the busted one back, not sure if that was true for sure but that's what the guy was saying. His chip fried and they sent out a new one. I would be interested to find out if someone else that runs into issues down will be able to do the same thing and have cloupor send them one direct instead of having to go through vendor as middle man.
What about the red window? Did some of the originals have that?
Oh ya. I did post this in another thread but anyone see this or know what chip it could be or if its really in existence.
Don't know as the few video's I watched did not open them up...
Just got my first ever RDA!! Authentic Patriot with a .5 ohm build (local B&M worker showed me how to wrap them). So amazed by the flavor and the copious amounts of vapor!!
blk on blk looks really nice!
i picked up a blk tobeco kfl+ / blue M-tank and just finished a custom drip tip (yellow/orange/flame treated blue 316L stainless ( to match the flamed lower chimney )). the atty looks pretty decent on the orange cana.
i am not going to put any atty below 0.8 ohms on the cana and recommend you don't go below 0.6 as already stated in this thread.
Last edited:
Been using my canas for 2 weeks now and man they are great! Mostly 0.8-1.2 ohm in a kayfun or kayfun lite with cotton at 17-22 watts.
Cons are they scratch easy(vtr didn't have that), the charging light is very weak and sometimes they need a double click.
Verstuurd vanaf mijn SM-N9005 met Tapatalk
Cons are they scratch easy(vtr didn't have that), the charging light is very weak and sometimes they need a double click.
Verstuurd vanaf mijn SM-N9005 met Tapatalk
How far back is the PSA about not throwing anything below a .6 on there? I'm only vaping at 15 watts at this point. I won't be going above that until I start wrapping my own coils.
I'm still waiting on mine to come but in a vape shop today. I got to play with one (clone) and they got to try my sx350 mod. The clone he had did the same thing. Had to click twice. Once to bring it out of sleep and the second one fired it. Once it was out of sleep it fired every time.
Sent from my iPad using Tapatalk
Sent from my iPad using Tapatalk
Gotta be the same as the hCigar being that those are the completed mods they sell
Ha ha you just couldn't stay away could you?
Let us know what you think.
Also I noted the warranty claim on the manual as well. This actually could have some bearing on retailers.
Make mine green. The hCigar logo looks WAY better than Hanas
Yep.... could be a good thing for the US vendors.... especially if they start getting alot of returns due to issues...
Care to say what vendor and order #. I ordered orange from elev8
Got mine from wetvapes yesterday.
The led doesn't turn green after charged.
It does seem to fire every time on first button press.
I ordered another from elev8 ,but still waiting on it.
I really like the mod.
Sent from my iPhone using Tapatalk
The led doesn't turn green after charged.
It does seem to fire every time on first button press.
I ordered another from elev8 ,but still waiting on it.
I really like the mod.
Sent from my iPhone using Tapatalk
- Status
