Weird, it shows a 1.2 as 1.2 pretty accurate in that range, but over say 2.5 it reads low.
Attack of the Hana Modz Clone. Let's wait together!
- Thread starter Fathomrock
- Start date
- th_trl_thread_readers 0
- Status
I don't have any that high... Think I have tested a 2.3 that read as 2.2. I didn't realize people use such high resistances still
LOL , don't usually go that high, but I've got some fav juices in older iClear30S's that I should change the heads on. (cheep cheep)
Bought a blue at 10:03PM- everything was in stock except orange (even GREEN). Sold out at 10:15- either they didn't have many, or....... ?
Anyway, I got my blue and canceled my Vaportek order.
Good point- Don't tighten the attys to much! Just finger tight. That center pin in the clone doesn't have much "give" and it's a very large diameter- some of the short issues and
'check atomizer" issues may be related to over tightening. Adjust the atomizer center pin if necessary (and it is adjustable...)
LOL , don't usually go that high, but I've got some fav juices in older iClear30S's that I should change the heads on. (cheep cheep)
Ah, I see! I've recently adapted a new moto, before I got deep into rebuildables, if I can't rebuild it I don't want it. When I first started vaping I spent roughly 1/2 of what I spent on cigarettes a month on coil heads, while they're inexpensive $1.75 a pop I think maybe $1.95, it was just an unneeded expense when I could replace with a micro coil for pennies.
For sure, I just got my new glasses yesterday and it looks like I'll be building coils again. So good to be able to see properly again.
just got mine in today have to say the finish is very very nice.
so far i can only use my nautilus as my drippers positive post is pooched but i am very pleased with this mod so far!
just hope it will live and that i can find a dripper with a spring loaded pin or one poking out so it doesn't fry.
so far i can only use my nautilus as my drippers positive post is pooched but i am very pleased with this mod so far!
just hope it will live and that i can find a dripper with a spring loaded pin or one poking out so it doesn't fry.
I was thinking about taking mine apart to poke around and see if something looked off and if that didn't work get the dna30. Evolve is out but I found a few vendors with stock at ~$49.95. I wonder why they're twice as much in Europe..
But I digress. Recieved a response to my email to send it in. If/when the replacement poops I should have a DNA30 chip ready. Kinda wish i just went with a Vaporshark from the get go though..but you know what they say about hindsight.
But I digress. Recieved a response to my email to send it in. If/when the replacement poops I should have a DNA30 chip ready. Kinda wish i just went with a Vaporshark from the get go though..but you know what they say about hindsight.
Anyone looking for a clone in stock? I just seen what looks to be a cloupor clone on clouds of vapor, waiting for confirmation
it looks like it. only in black though. plus its $99
Sent from my SCH-I545 using Tapatalk
should be just resistance, not voltage. it means thay it is firing below volts, anf should theoretically act like a mech mod where you experience voltage drop.
Sent from my SCH-I545 using Tapatalk
Update: the roller coater ride continues. put a battery in (efest 2500mAh purple) for the 20th time, screen was comletely black. Began hitting all the buttons in every combination and repetition I could think of and suddenly heard the familiar crackle. It was firing in stealth! Jacked with the buttons again and somhow got in back in normal mode and it's working again. The kicker is that 4 clicks, not 5, takes it in and out of locked mode now. Other than that every thing is currently working as it should. knock on wood. hard.
It means you have the wattage set too LOW for what the mod can regulate. If your wattage as per the resistance of your coil requires LESS than 4volts the mod will not regulate power to your coil and the voltage will be whatever your battery has.
So turn the pwr up until it stops flashing and displays 4v and that will be the lowest you can go regulated.
- Status
