Bauway 2.4 to 2.7 oHM Atomizers

[FreeFlow]

So i bought a few of these "very high vapor production" atty's and they are great. They do seem to produce more vapor. The supplier website suggests to prime with 1 or 2 drops directly in the atty before you insert your cart. They say to do this because they perform best wet. OK cool, no prob, done.

My question is how long should it be before i have to do this again? I prime it and vape for abit and its great. But after a short time (3-5 mins) I start tasting plastic. My cart is full, I see a small pool of liquid on top of the cart indicating to me that I do not need to top it up. Normally, when I taste plastic it's time to top up.. not the case right now. I can direct drip on the atty and the plastic taste is gone for awhile again.

So do I need to "prime" this atty after every small vape session?
It is brand new, maybe that's why?


Any input is greatly appreciated.

 

[nubee]

Looks/Sounds like classic LR attys so the rule of thumb is the wetter the better. Not really priming it but just keeping the amount of juice available to the coil and a higher than "usual" level.

You might want to look at some of the cart mods around the forum as some might allow for better/faster/higher flow from cart-to-coil.

 

[FreeFlow]

These are not Low Resistance atty's, the supplier also sells those and i don't have the proper battery for it. i'll post a link below to the atty I'm asking about.

Bauway510 Atomizer (Black)

 

[basilray]

OP: You might want to look into dripping, which is practically what you are doing with that atty.

Also, if the cart is that wet, but not gaping well, it may not be getting to the wick. Try a different cart, making sure the filler is not packed too tightly, it will keep the juice from wicking.

 

[sanfordf]

I suggest the HighPing filler mod. Simply cut the filler in half, fill cart with fluid to about 1/8th of an inch from the top, reinsert the halved filler until it is level with the top of the cart. It should look wet, if not add a drop or two. The filler will self adjust to the tip of the bridge of the atomizer, insuring contact. With LR atties, it gets hot quicker and vaporizes the juice quicker, producing good vapor while it has juice available. That's the key. Dripping is one way to ensure a wet atty. Another is to never use just one unit. Keep several in rotation. Using one unit too frequently dries the filler faster than it can wick to the attie. This causes the off taste.

 

[FreeFlow]

I suggest the HighPing filler mod. Simply cut the filler in half, fill cart with fluid to about 1/8th of an inch from the top, reinsert the halved filler until it is level with the top of the cart. It should look wet, if not add a drop or two. The filler will self adjust to the tip of the bridge of the atomizer, insuring contact. With LR atties, it gets hot quicker and vaporizes the juice quicker, producing good vapor while it has juice available. That's the key. Dripping is one way to ensure a wet atty. Another is to never use just one unit. Keep several in rotation. Using one unit too frequently dries the filler faster than it can wick to the attie. This causes the off taste.

Will blue foam work?

 

[sanfordf]

It should, but I don't use the blue foam mod and you'll need to experiment with the HighPing mod to see what length (if not the 1/2 size) to trim it to. It is good to never let the atty or cartomizer to completely dry out. They last longer. Don't get so crusty or burnt.

 

[FreeFlow]

I've used the highping mod and it worked well. I just don't have any polly anymore, will try it with blue foam. This should work, thanks for the tip, can't believe i didn't think of it myself..