BF addy modders
- Thread starter puffon
- Start date
- th_trl_thread_readers 0
- Status
I will be watching this thread.
I did a Patriot with success and failed on a Lethal. I only have Dremel tools and would never take on a project for someone else.
I did a Patriot with success and failed on a Lethal. I only have Dremel tools and would never take on a project for someone else.
If you guys where is South Africa you would have been in luck. We have a store here VapeClub that is a BF Modder genius. He does amazing work on any Rda.
Sent from my iPhone using Tapatalk
Unfortunately that's all some of us can afford at the moment, so I won't be able to send him anything any time soon.
I may try the conversion kit from Fat Daddy Vapes. Just depends on how adventurous I'm feeling.
Do you have a link? I am sure an influx of dollars would not be a bad thing.
Yes no problem.
www.vapeclub.co.za
Email - info@vapeclub.co.za
His name is Jaco and he is a awsome guy.
Sent from my iPhone using Tapatalk
Dremel and the dremel drill press setup and a handful of titanium drill bits like 1/16 size and take ur time with it and get it done yourself Like I have.
If it's done with the pin installed go slow hit it for a few seconds and lift the drill bit off. Kinda like a 3-4 count drill and off.. I did that 2 or 3 times in a row and then I would stop and blow on the atty to help keep the heat down as you don't want to melt the insert Around the post if it's a one piece Post.
Use a drop of any kind of cooking oil on the bit.. even after all thst I didn't manage to break a bit but I did wear it out.
If it's done with the pin installed go slow hit it for a few seconds and lift the drill bit off. Kinda like a 3-4 count drill and off.. I did that 2 or 3 times in a row and then I would stop and blow on the atty to help keep the heat down as you don't want to melt the insert Around the post if it's a one piece Post.
Use a drop of any kind of cooking oil on the bit.. even after all thst I didn't manage to break a bit but I did wear it out.
Took me like a half hour to drill out the post and it was mostly hollow! Haha.. only had like a quarter of an inch or less to drill.. the juice holes on top were free hand with the dremel. You need to dull the post first where you want to drill or your bit will dance off the post. I used an engravers dremel bit to do that as its all I had.
Here is the new Rogue rda that he Bf. I know it show out of stock but he still have to bf them. Just drop them a mail.
Sent from my iPhone using Tapatalk
I use a table vise to hold the base of the atomizer. The patriot drilled clean but the Lethal suffered a broken pin.
Nobody has yet mentioned using a dremel cutting wheel to score a channel up the side of the centre pin, but that works fine too and i've done that on a couple of Atomics, rather than try to drill ss.
T
T
Do they sell them modded for bottom fed or do ones people send in ?
Cant find bottom fed on the site.
Never mind , not in South Africa.
They sell them BF and you can send it to them.
Just drop them a mail and let them know what you are looking for.
Sent from my iPhone using Tapatalk
I've done the same thing to mine long ago! Haha.. that was a crazy atty to mod for me for some reason.. remember having a hell of a hard time getting the post ou of it. 8 remember some crazy contraption I came up with prob using a clamp or 2 and a pipe wrench. Hehe
Yup scored it on both sides of the post and then pushed it back up in there and it was all set.
Per their website they do not ship outside the borders of South Africa.
+1. It's easy as pie and performs just as well as a hole drilled through the center of the pin.
- Status
