Catfish atty mods.
- Thread starter Chowderhead1972
- Start date
- th_trl_thread_readers 0
- Status
Bob, you are always straight up. And I like that. You are always right too. 3 posts barely fit in the Atomic... so now that I think about (thanks BobC) i can't imagine 14mm with 3.
And yes chowder. I'd like a Reactor...
-Mark
Did I read somewhere Divos are coming??? I need another if there is a "I need another" list!
Like the new avi!! 
Old one always made me laugh every time I saw it. Reminded me of summertime on boardwalk in AC 
Old one always made me laugh every time I saw it. Reminded me of summertime on boardwalk in AC 
If you are happy with the polycarbonate clear tube as well as the stainless tube section pay me now and it will go out in the morning. If you are holding out for glass pm Turk and have him add you to the spreadsheet.
+1 to this. 3 pekos, all with vapage bottles, all see lots of use. Never used the gaskets they come with.
No leaking. The only bad thing about these bottles is that you need needle tips, or at least the thin tip, bottles to refill them. That's literally it. I think I used an 11/64 bit to drill them for 3/16od 1/16id 1/16wall thickness tubing.
I like the ones I have so much that I ordered 20more.
sent via Droid Mini
Last edited:
Tom, what's the difference between the stock hornet pins and VA bf pins? Thanks
Know nothing about the PDA's. But the three posts in my A6/RM3's have not been hard to build duals on. You can't get too slap happy with wick, but they work quite well as bf's FWIW.
Hey peeps, I'm late to the party. Looking for solid stainless steel rba/ bf with stainless posts and some afc. I'm wanting something not too large to use with the REO.
Anyone have suggestions?
P. S.
I mainly build single or dual coils.
Thanks in advance!
Anyone have suggestions?
P. S.
I mainly build single or dual coils.
Thanks in advance!
There's quite a lot to choose from Moonbear.. someone will soon post the spreadsheet with already available and rda's coming soon! If you see a post from "TheTurk" click his signature to take you to the Google spreadsheet!
-Mark
-Mark
not at this moment mark but a lot of times I do get rid of attys after a bit.i will let you know if I get ready to let it go though.i do have a slick mini reo that I filed down to an lp that needs a good home and a few diff attys I just haven't got them on the classies yet.i don't have a camera to take pics so I have to wait for the kid to stop by and take them for me.i have learnt to post pics though,if ya hear of anyone lookin lemme know.
Ahh, I fired up my Reactor just today.
Awesome performance, all day, and it was a loooong day, too.
Not a hint of leaking, intense flavor with my "tight/restricted lung hit" holes (tip - don't try to drill a reactor with a hand drill), running 0.7 ohm 28g dual. Gotta rebuild it just a little lower, like 0.5.
Awesome performance, all day, and it was a loooong day, too.
Not a hint of leaking, intense flavor with my "tight/restricted lung hit" holes (tip - don't try to drill a reactor with a hand drill), running 0.7 ohm 28g dual. Gotta rebuild it just a little lower, like 0.5.
Agreed; the Reactor was awesome. I can have them made by the original manufacturer (Madz Modz).... But I have to buy 200 of them, that would require a serious dibs list. If I ever finish all of the Derringers I have a meeting with a machine shop to hash out my ideas. My front runner is the reactor crossed with the Derringer with a coned/dished deck with a twisted "T" center post. Psyched yet?
This is the VA bf pin? So does the stock pin have a hole at deck level?
- Status
