[CLOSED]
- Thread starter Tbev
- Start date
- th_trl_thread_readers 0
- Status
Just looks spanking gorgeous!
Sent from my iPhone using Tapatalk
Can't get over how shiny you have that mod robbie! Looks fabulous [emoji4]
Sent from my iPhone using Tapatalk with my paws
Mommabird62
Looks good sXd! How do you compare the Thump to the Stumpy, my all time fave 22mm? [emoji6]
Sent from my iPhone using Tapatalk with my paws
Mommabird62
Looks good sXd! How do you compare the Thump to the Stumpy, my all time fave 22mm? [emoji6]
Sent from my iPhone using Tapatalk with my paws
Mommabird62
They are both off the chain. I'm selling some stumps to get more thumps. By the time you read this you will have already bought a stump. I have ESP
Mountaintop Zombie TMod vid?Fer sure. Sloth vids are the shizz
Sure bro
give me til midweek
I am tempted to throw the TMod off the mountain, hike down, find it, and vape it...because I'm pretty sure this beast of a mod could take that just fine
Remove the battery first. That would be messy.
Remove the juice bottle first. That would be a waste.
You'll prolly put some scratches on the finish. But once you put the battery and bottle back, you'll have a freight train in your hand.
They are both off the chain. I'm selling some stumps to get more thumps. By the time you read this you will have already bought a stump. I have ESP
LOL you do have ESP sXd! [emoji12] Have six of those babies now [emoji4]. Thanks!
Sent from my iPhone using Tapatalk with my paws
Mommabird62
Dope pic!
Sent from my SM-G900V using Tapatalk
Sent from my SM-G900V using Tapatalk
Sloth, just fyi, to adjust the height of the atty this is what you do:
DO NOT ADJUST WITHOUT REMOVING THE LOCKNUT.
After you remove the locknut spin thw positive pin clockwise (down) and put your atty back on, when your atty is at desired height, spin the positive pin up, from below, till it makes good contact with the pin of the atty.
Then remove the atty and hold the pin (from above) with a Phillips screwdriver, in place and tighten the locknut from below.
Make sure your contact bar is perfectly streight. If you have any questions feel free to shoot me a pm.
Sent from my SM-G900V using Tapatalk
DO NOT ADJUST WITHOUT REMOVING THE LOCKNUT.
After you remove the locknut spin thw positive pin clockwise (down) and put your atty back on, when your atty is at desired height, spin the positive pin up, from below, till it makes good contact with the pin of the atty.
Then remove the atty and hold the pin (from above) with a Phillips screwdriver, in place and tighten the locknut from below.
Make sure your contact bar is perfectly streight. If you have any questions feel free to shoot me a pm.
Sent from my SM-G900V using Tapatalk
Thank you Tom I was wondering, and will attempt it today. May have a Q or two, will let you know bro
I was wondering, and will attempt it today. May have a Q or two, will let you know bro 
Oh I am sure it would be fine. Here is mine after it fell out of my pocket at a go cart track. Working great now after some cosmetic surgery by Tom.I am tempted to throw the TMod off the mountain, hike down, find it, and vape it...because I'm pretty sure this beast of a mod could take that just fine
Before
After
Sent from my SM-N910V using Tapatalk
Last edited:
Looks pretty good, maybe a little more sanding will get the rest. But not looking bad.Oh I am sure it would be fine. Here is mine after it fell out of my pocket at a go cart track. Working great now after some cosmetic surgery by Tom.
Before
After
Sent from my SM-N910V using Tapatalk
But if you had gotten 7075 you would have left a trench in the track.....Oh I am sure it would be fine. Here is mine after it fell out of my pocket at a go cart track. Working great now after some cosmetic surgery by Tom.
Before
After
Sent from my SM-N910V using Tapatalk
- Status
Similar threads
