[CLOSED}

[inswva]

What mode do you run the 316L in on sxj? Ni, ti or put in a coefficient ? Also what kind of temp?
For those who use 316 SS on dna40 do you have to turn temp down vs nickel temps?

I've only been able to run 316L in power mode on a DNA40. TC is no bueno.

 

[McPuff]

What mode do you run the 316L in on sxj? Ni, ti or put in a coefficient ? Also what kind of temp?
For those who use 316 SS on dna40 do you have to turn temp down vs nickel temps?

I'm running manual tcr mode. Set at .ooo92 at 33 joules temp set at 400. The coil is 3 pieces stainless 316L 28 gauge twisted together and wrapped around 2.5mm bit. .32 ohm single coil. It's flavorville. Kicks out some great vspor too

 

[McPuff]

I've only been able to run 316L in power mode on a DNA40. TC is no bueno.

Yes 316L on tc with dna40 = no go
Nice in power mode though

 

[havok333]

Tom, if you do a run of color Makers I'll be in for at least a blue.[emoji1]

Sent from my XT1049 using Tapatalk

 

[Raynman]

There's a bunch of them for sale, I think catfish might do a run as they have no logos. Just guessing though.

 

[Unior]

I'm running manual tcr mode. Set at .ooo92 at 33 joules temp set at 400. The coil is 3 pieces stainless 316L 28 gauge twisted together and wrapped around 2.5mm bit. .32 ohm single coil. It's flavorville. Kicks out some great vspor too

Thanks that's what I needed to know.
I've got some 430ss & I didn't have much luck with it using manual TCR. I have the coefficient chart so I know I had the correct values. I tried 25 & 27g but only one coil each. I had temp up pretty high(500) & not that many joules(22) & it was hitting temp too quick. Thought it might just be device but I'm pretty sure your using a Scudo too. Got some 316 I'm about to try though. But from what I've heard 430 is better for TC. Maybe I'll get a chance to play around with it soon.

 

[McPuff]

Thanks that's what I needed to know.
I've got some 430ss & I didn't have much luck with it using manual TCR. I have the coefficient chart so I know I had the correct values. I tried 25 & 27g but only one coil each. I had temp up pretty high(500) & not that many joules(22) & it was hitting temp too quick. Thought it might just be device but I'm pretty sure your using a Scudo too. Got some 316 I'm about to try though. But from what I've heard 430 is better for TC. Maybe I'll get a chance to play around with it soon.

Are you locking your resistance and ambiance temp? That would cause problems. I'm using my only top fed mod for the ss wire. The scudo doesn't have the programing in it for ss wire yet.

 

[Chowderhead1972]

The first 10 LBCs are ready to ship minus the inlay being installed. Transfer tape is supposed to be here tomorrow to facilitate such. I just couldn't bring myself to superglue it.
Profiles 1 and 2 are 316, 3 and 4 are NiFe30, 5 and 6 are titanium, 7 and 8 are up to you.



All charged, all programmed

 

[Nautilusfan]

The first 10 LBCs are ready to ship minus the inlay being installed. Transfer tape is supposed to be here tomorrow to facilitate such. I just couldn't bring myself to superglue it.
Profiles 1 and 2 are 316, 3 and 4 are NiFe30, 5 and 6 are titanium, 7 and 8 are up to you.



All charged, all programmed

Excellent!! I'm pretty excited Glad you refrained from using the superglue..

Soooooo will probably ship on Thurs? If so I should have it Sat.

 

[Chowderhead1972]

Excellent!! I'm pretty excited Glad you refrained from using the superglue..

Soooooo will probably ship on Thurs? If so I should have it Sat.

You will see the tolerances on this thing when you get it... Part of what took so long is all the parts were spect to a variance no greater than .05mm. Most places wouldn't even touch my prints as soon as they saw the spec. The carbon guy is still having night terrors.... The body is machined so precisely if I used superglue there would be a .2mm recess at the inlay. That's how it is on my red one just because I could wait any longer. My second one will be correct.

For reference a sheet of 20lb printer paper is .1mm thick.

 

[Chowderhead1972]

Excellent!! I'm pretty excited Glad you refrained from using the superglue..

Soooooo will probably ship on Thurs? If so I should have it Sat.

The first ten should definitely go out Thursday. The second ten Friday or Saturday.

 

[RickCain]

The LBC looks amazing Tom! Can't wait to see you shipping out your creation for everyone to enjoy.

 

[Nautilusfan]

You will see the tolerances on this thing when you get it... Part of what took so long is all the parts were spect to a variance no greater than .05mm. Most places wouldn't even touch my prints as soon as they saw the spec. The carbon guy is still having night terrors.... The body is machined so precisely if I used superglue there would be a .2mm recess at the inlay. That's how it is on my red one just because I could wait any longer. My second one will be correct.

For reference a sheet of 20lb printer paper is .1mm thick.

Variance of .05mm..... Wow... Just shows how truly amazing these mods are!!

 

[Chowderhead1972]

For example: look how tight that seam is. Also look at the relief cut in the carbon for the magnets.

 

[Mactavish]

Well even though I can't afford one, I just have to say: GREAT JOB Tom! Beautiful work.

 

[Nautilusfan]

Really nice Tom!! Gonna be worth the wait
So glad you chose to produce a product that exemplifies quality and planning. Shows what can be done when a modder has the knowledge and patience to produce a product they can truly be proud of

 

[goofy2302]

Ahhhhhhhhh...i wont be home next week...ill be on the road....more torture......

Sent from my SM-N900T using Tapatalk

 

[Chowderhead1972]

Let's do a quick 24hr quick old school list for Makers and Petris. Specify colors
Maker:
1. Chowderhead72 Blue
2.



Petri
1. Chowderhead72 black

 

[Slots]

Tom, ... any chance of you posting a picture of each, or do I have to go back 100 pages
Also, will the black ones be solid black, or do they still have writing on them.
Sorry to be a pain .. but need to be "refreshed" if possible

 

[havok333]

Let's do a quick 24hr quick old school list for Makers and Petris. Specify colors
Maker:
1. Chowderhead72 Blue
2. havok333 Blue



Petri
1. Chowderhead72 black