[CLOSED}

[bigTRAV710]

Threw a new build in my maker dual 5 wrap 22g 3mm id at .16 ohm on the lbc at 70watts , so good. Im not sure how low i should drain the battery before i charge it? This is my first lipo mod.

 

[pwheeler]

I've had mine down to 4% before. Works great even getting down below 10%.

 

[Irish Messing]

Im not sure how low i should drain the battery before i charge it?

Meh, vape her till she shuts down if you like (right around 4%). Just don't do like I did and only have one...then you have to wait for her to come back to life...charging times can be sad times.

 

[bigTRAV710]

Meh, vape her till she shuts down if you like (right around 4%). Just don't do like I did and only have one...then you have to wait for her to come back to life...charging times can be sad times.

Lol thanx, i have a CC and a Tmod in the rotation at home and a dna75 with a tank for work

 

[bigTRAV710]

Does the dna200 just default to power mode with kanthal? My dna75 has a kanthal preset , but i dont see it on the LBC

 

[havok333]

Does the dna200 just default to power mode with kanthal? My dna75 has a kanthal preset , but i dont see it on the LBC

Yes, it will just work in poser mode automatically when not using tc wire. Within escribe you can have a preset set to always use power mode if you like.

Sent from my XT1049 using Tapatalk

 

[Irish Messing]

Ohh, don't get me wrong, I have CCs and other mods (even ones that have bars covering the squonk hole ). But...backups for backups. To be without an LBC sucks no matter how you cut it.

I don't think there is any "profile" so to speak for kanthal. No temp control that I know of.

 

[bigTRAV710]

The Lbc is working great, looks amazing, and smaller than i thought it be .These soft bottles are awesome , i keep over sqounking, cause im used to a firmer bottle.
I don't like temp control , the vape just always seems weak to me. I like a warm warm saturated vape.Now all I need is a goon to put on top of this beast!!

 

[Train2]

The Ch-O-Attys are ready. Who's in. I do them bottom fed for 45 or bottom fed with HD terminals (m2.5) for 55. (Plus $7 for shipping).

1. distortoblotto (HD)
2. distortoblotto (HD)
3. havok333 (HD)
4. havok333 (HD)
5. Tagi (HD)
6. Tagi (HD)
7. ghola1was (HD)
8. Boobsley (HD)
9. Beez0527 (HD)
10. Kingdal
11. Train2

 

[Train2]

Can you explain as if i was an idiot (as if ) about the terminals ? What's different and why I'd want it?

The Ch-O-Attys are ready. Who's in. I do them bottom fed for 45 or bottom fed with HD terminals (m2.5) for 55. (Plus $7 for shipping).
1.

 

[Henry Etta]

Someome remind me, is the Ch-O-Atty suitable for MTL?
I'm a tootlepuffing wimp that still makes RM2 clones with a single 1.5mm hole.

My experience is no. It will close down, but IMO it doesn't work well with real restricted air.

 

[Chowderhead1972]

Just opened my pearl white LBC , its bad ace!!!! Thanks Tom. Is there not a kanthal preset?

Numbers 7 and 8 should be stock. These have all been updated to service pack 2.

 

[Chowderhead1972]

Can you explain as if i was an idiot (as if ) about the terminals ? What's different and why I'd want it?

The hardware on the O terminals are either #1 or #2 bolts. Very fragile, my authentic was threaded incorrectly from the factory on the negative post and I was certain the bolt would snap off in the hole if pushed. I gently extracted the damaged bolt and bored and threaded for m2.5. I installed m2.5 hex cap bolts and the head fits the slot perfectly. Solid connection and got rid of the fiddley plates but kept the concept with the proper sized bolt head. Win/win.

 

[Chowderhead1972]

My experience is no. It will close down, but IMO it doesn't work well with real restricted air.

I would suggest the Narda or Chi-Narda for such uses. The O Atty is very much like an updated version of the nNarda. Easier to coil, 20% more air, 75% less noise. If the Narda bordered on too loose for you, you will not enjoy the O. If you like the Narda but feel like you need a little more air the O is your speed.

 

[Chowderhead1972]

Threw a new build in my maker dual 5 wrap 22g 3mm id at .16 ohm on the lbc at 70watts , so good. Im not sure how low i should drain the battery before i charge it? This is my first lipo mod.

It will let you know. The board will protect the battery. What the board will not do however is protect itself if you get a short at full power when using stainless. This occurs with high power builds with wire big enough and close enough to the edge of the cap that upon the expansion of the coil due to heat it makes contact with the cap and shorts out under load. Not a common occurrence but it has happened. When building with ss you might consider leaving a solid millimeter or more between the coil and cap. Just an update to a previous psa....

To clarify: if the build or atty is shorted at the start it will protect itself and the mod. The issue only presents itself when the short occurs under load.

 

[Chowderhead1972]

The Lbc is working great, looks amazing, and smaller than i thought it be .These soft bottles are awesome , i keep over sqounking, cause im used to a firmer bottle.
I don't like temp control , the vape just always seems weak to me. I like a warm warm saturated vape.Now all I need is a goon to put on top of this beast!!

I vape exactly the same. Hot and very wet. (There is a joke in there somewhere, I'm sure of it).

 

[Kentastic]

The Ch-O-Attys are ready. Who's in. I do them bottom fed for 45 or bottom fed with HD terminals (m2.5) for 55. (Plus $7 for shipping).

1. distortoblotto (HD)
2. distortoblotto (HD)
3. havok333 (HD)
4. havok333 (HD)
5. Tagi (HD)
6. Tagi (HD)
7. ghola1was (HD)
8. Boobsley (HD)
9. Beez0527 (HD)
10. Kingdal
11. Train2
12. Kentastic (HD)

 

[Train2]

The Ch-O-Attys are ready. Who's in. I do them bottom fed for 45 or bottom fed with HD terminals (m2.5) for 55. (Plus $7 for shipping).

1. distortoblotto (HD)
2. distortoblotto (HD)
3. havok333 (HD)
4. havok333 (HD)
5. Tagi (HD)
6. Tagi (HD)
7. ghola1was (HD)
8. Boobsley (HD)
9. Beez0527 (HD)
10. Kingdal
11. Train2 (HD)
12. Kentastic (HD)

 

[snakedoc]

Tom,
Any chance of an XL mod with dna 250 and bigger lipo?

 

[kingdal]

The Ch-O-Attys are ready. Who's in. I do them bottom fed for 45 or bottom fed with HD terminals (m2.5) for 55. (Plus $7 for shipping).

1. distortoblotto (HD)
2. distortoblotto (HD)
3. havok333 (HD)
4. havok333 (HD)
5. Tagi (HD)
6. Tagi (HD)
7. ghola1was (HD)
8. Boobsley (HD)
9. Beez0527 (HD)
10. Kingdal (HD)
11. Train2 (HD)
12. Kentastic (HD)

Just updated my slot to HD...