[CLOSED}

[havok333]

You can get the rubber 18650 holders off eBay, with a lil streching they fit fine. I also got some custom built 3d printed holders but I'm not sure he's going to do them again as they took a lot more time and work than he expected.

Sent from my LGL33L using Tapatalk

Thanks, I'll check the stretchy things out. I do have some zipper cases made to hold a few 18650s that may be large enough to work.

Sent from my XT1585 using Tapatalk

 

[havok333]

I designed and printed some 3 and 4 20700 holders for my desk that I published on Thingiverse. They are bulky but very tough.

That's really sharp! [emoji106]

Sent from my XT1585 using Tapatalk

 

[havok333]

For one mod 4 should be more than sufficient. Figure one in the mod, 1 in the pocket and 2 on the charger. Personally I vape at 50w +/- 5w and I get a a no BS 12-14hrs on one battery. Typically when I get home from an 8 hour day plus half hour commute each way I'm always between 40% and 60% charge remaining. This is while using one of my 24mm Flaves with a Mr. Williams approved SS 28/32 clapton single coil. With a single 24g ss coil in the Flave that number drops by 2 hours. That's with the real Sanyo 20700A's. With the Ijoy 20700s those numbers are about an hour less. The 20700 and DNA75 are a much better pairing than the 3s 950 and the DNA200.

I have read similar experiences with longevity of the 20700 Batts, and definitely looking forward to giving them a test drive.

Honestly, being an office rat all day I'm always near USB charging, so the LBC works out nicely. I do drain them down rather quickly at 75+ watts though.

Sent from my XT1585 using Tapatalk

 

[beez0527]

Here's my printed one from a group buy in fb group Squonk america

Sent from my SM-P607T using Tapatalk

 

[plumeguy]

Let's do a list for real Sanyo 20700A batteries. This will be an ECF only list for the next few weeks.
How's $14 per cell sound?

1. Chowda x2
2. Cveez11 x2
3. sirvthondaguy08 x2
4. Beez0527 x4
5. havok333 x4
6. Snakedoc x4
7. Penguiness x4
8. Boobsley X4
9. Kentastic X3 (because I'm a little odd)
10. Plumeguy X4

 

[TwistedThrottle]

Let's do a list for real Sanyo 20700A batteries. This will be an ECF only list for the next few weeks.
How's $14 per cell sound?

1. Chowda x2
2. Cveez11 x2
3. sirvthondaguy08 x2
4. Beez0527 x4
5. havok333 x4
6. Snakedoc x4
7. Penguiness x4
8. Boobsley X4
9. Kentastic X3 (because I'm a little odd)
10. Plumeguy X4
11. TwistedThrottle x2

 

[TwistedThrottle]

@Chowderhead1972 sent ya an email

 

[Chowderhead1972]

@Chowderhead1972 sent ya an email

Replied... get comfy before opening the email.

 

[inspects]

Tom, long time no visit.

Can you get your hands on the new Narda (NarCa) by any chance?

 

[Chowderhead1972]

Tom, long time no visit.

Can you get your hands on the new Narda (NarCa) by any chance?

Sorry man, Nareg won't sell to anyone wholesale. I was the only one and that was only 50 pieces split up over 2 runs.

 

[Boobsley]

Enlighten me, I’ve not seen the NarCa. I even googled it & found nothing.

 

[Saltzman79]

Let's do a list for real Sanyo 20700A batteries. This will be an ECF only list for the next few weeks.
How's $14 per cell sound?

1. Chowda x2
2. Cveez11 x2
3. sirvthondaguy08 x2
4. Beez0527 x4
5. havok333 x4
6. Snakedoc x4
7. Penguiness x4
8. Boobsley X4
9. Kentastic X3 (because I'm a little odd)
10. Plumeguy X4
11. TwistedThrottle x2

12. Saltzman79 x2

 

[inspects]

Good ole, Mark Todd.

 

[inspects]

Let's do a list for real Sanyo 20700A batteries. This will be an ECF only list for the next few weeks.
How's $14 per cell sound?

1. Chowda x2
2. Cveez11 x2
3. sirvthondaguy08 x2
4. Beez0527 x4
5. havok333 x4
6. Snakedoc x4
7. Penguiness x4
8. Boobsley X4
9. Kentastic X3 (because I'm a little odd)
10. Plumeguy X4
11. TwistedThrottle x2
12. Saltzman79 x2

 

[Chowderhead1972]

I have 2 of these ready to build. These were an experiment but I just can't get the cost down to make them viable for production. 3d Ultem. Check out the shimmer!

 

[Chowderhead1972]

I have read similar experiences with longevity of the 20700 Batts, and definitely looking forward to giving them a test drive.

Honestly, being an office rat all day I'm always near USB charging, so the LBC works out nicely. I do drain them down rather quickly at 75+ watts though.

Sent from my XT1585 using Tapatalk

Email sent. Ready when you are.

 

[Alexander Mundy]

I have 2 of these ready to build. These were an experiment but I just can't get the cost down to make them viable for production. 3d Ultem. Check out the shimmer!

View attachment 697397 View attachment 697399 View attachment 697401

Did you sand the outside of those?
If not that is an awesome job of 3D printing Ultem.

 

[Chowderhead1972]

Did you sand the outside of those?
If not that is an awesome job of 3D printing Ultem.

I milled the flats and wet sanded them.
I wish they started off that clean. This is how they looked on arrival:

 

[Chowderhead1972]

So should I carry the 528 Squonkers? I'm still a 528 retailer. I could probably even save you a few dollars.

 

[Tamer El-Meehy]

So should I carry the 528 Squonkers? I'm still a 528 retailer. I could probably even save you a few dollars.

Hey Tom...been a while...hope you're doing fine.

been eyeing these since they came out, especially the DS. They look good, and definitely well priced. have you tried them? is there any review made for them by a serious squonker? How do they discharge the batteries? Will we be needing more spare bottles?


Sent from my iPhone using Tapatalk