Coil P0rn

[dripster]

Maybe a little off-topic because I like to refer to this type of coil build as my "bog standard", or "go to" sort of All Day Vape (27/36 Ni80, 5 wraps at 2.5mm ID) aliens dual coil at .11 ohms so it is the exact same set of coils that you could also decide to just buy from m.terk (Mike), in the District F5VE CSMNT on top of the Purge mods Suicide King Murdered Out.

As you can see in the pics I posted above, tightening the post screws didn't twist these coils out of shape in any way that could affect the final result, as you need (that is, at least IME) to slam them over to the outside to get them really close to the airflow, and, by doing this they are already straightened out properly anyway in the first place. In fact I prefer the CSMNT over the newer C2MNT because the latter would just increase the coil leg length for no reason. In addition, the reduced chamber size from the separately sold District F5VE Shawty cap is why the CSMNT is still ranked very close to the top on my list of alltime favorite flavor chasing RDAs.

 

[Tralfaz]

Agreed. I bought a couple of C2MNTs when they came out and they're perfectly fine but I do still prefer the original CSMNT.

Old pic with some Ni80 tri-core fused claptons on my Trinity Glass Hardware US1.

 

[Tralfaz]

Some tri-core Ni80 27/36 aliens at .11 in my Terk V2 on my Purge Truck 21700.

 

[Marper]

Mechlyfe twin mesh

 

[Blitzdonlife]

Mechlyfe twin mesh View attachment 857807 View attachment 857809

Best looking mesh coil setup I've seen. That dual honeycomb pattern is beautiful.

 

[Marper]

Yeah, its a really nice vape as well, easy to build and you won't get hotspots as the mesh roll is quite small

 

[Marper]

I'm using it on my crea mech in squonk mode, the juice squirts through the centre hole into the well and the wicks then soak it up,very good

 

[Marper]

Simple 6 wrap ni80 24g on my pulse 24 rta, had to go for it cause its rubbish with mesh, surprisingly good,4mm wrap,spaced,.7 ohms

 

[AngeNZ]

Simple 6 wrap ni80 24g on my pulse 24 rta, had to go for it cause its rubbish with mesh, surprisingly good,4mm wrap,spaced,.7 ohms
View attachment 857961 View attachment 857963View attachment 857965

I love how you think outside of the box

 

[Rob B.]

Simple 6 wrap ni80 24g on my pulse 24 rta, had to go for it cause its rubbish with mesh, surprisingly good,4mm wrap,spaced,.7 ohms
View attachment 857961 View attachment 857963View attachment 857965

That is cool right there!

 

[Marper]

Thanks but the capillary action with the cotton leaves a lot to be desired, it needs more mass to draw the juice, however, I have some premade flaptons and I think I'm going to rewrap 2 of them making 4 wraps each,both are ni80 and I think. 25 ohms so I should be good to go with one on top of the other, will post when I get round to it

 

[Marper]

Thanks, it works very well but you can't chain it, its better than what it was with the mesh, I think I'm on to something with more mass to suck the juice

 

[Don29palms]

Thanks but the capillary action with the cotton leaves a lot to be desired, it needs more mass to draw the juice, however, I have some premade flaptons and I think I'm going to rewrap 2 of them making 4 wraps each,both are ni80 and I think. 25 ohms so I should be good to go with one on top of the other, will post when I get round to it

I think you're just using too much cotton on the bottom of the coil. Try just pulling the cotton through just enough to touch the deck. That's how I do it in my vertical builds and it works just fine. I must also say I use rayon wicking.

 

[Marper]

I think you're just using too much cotton on the bottom of the coil. Try just pulling the cotton through just enough to touch the deck. That's how I do it in my vertical builds and it works just fine. I must also say I use rayon wicking.

Thanks,I'll try less cotton but it won't be easy to dam the juice holes, the vv 24 has 4 holes and it's a pain to keep the deck from flooding, very badly designed tank,totally useless with mesh

 

[Don29palms]

Thanks,I'll try less cotton but it won't be easy to dam the juice holes, the vv 24 has 4 holes and it's a pain to keep the deck from flooding, very badly designed tank,totally useless with mesh

My mistake. I didn't realize it was an RTA. I thought it was an RDA. Sorry.

 

[Marper]

It's only an experiment to try to make use of a tank made for mesh but doesn't work well with mesh, too much cotton and too much mesh, only ever got it working once and then the flavour was terrible, I won't give in,I'll find a way to get it working good enough for a decent vape if it kills me Haha

 

[badinfluence357]

First time ever using a prebuilt coil. 4 core fused clapton, 28g x 4 + 38g, 5 wraps. Im shocked just looking at the precision of the 38g wire clapton...Im sure they used a maching, not one overlap or error...

Sent from my SM-G950U1 using Tapatalk

 

[Skunk!]

Old school. Sleeper coil

 

[Tralfaz]

A couple from the past month...

Ni80 tri-core fused claptons in my Axial on my white RCM SHRTGN.

More Ni80 tri-core fused claptons in my polished Unicorn RDA on my Purge Truck 21700.

 

[icepickmaker84]

Put these in the S.C. Glaz. 4mm id and the pair comes out to .18. Made with alien wire I got for Christmas.