DNA 200 Watt

[BlueridgeDog]

I'm in.

Great. I have one coming from them at the moment. I suggest I do rough triage for alignment and then open it up for test orders.

 

[Mad Scientist]

EVOLV DNA200

Ok, I'm sitting here ready to pull the trigger on a preorder of board only. I see protovapor also has a preorder open. Any feedback on which vendor might be preferable to another?

 

[BlueridgeDog]

Ok, I'm sitting here ready to pull the trigger on a preorder of board only. I see protovapor also has a preorder open. Any feedback on which vendor might be preferable to another?

If you are a verified member, you can get one sooner and cheeper if you search this forum.

 

[Mad Scientist]

If you are a verified member, you can get one sooner and cheeper if you search this forum.

Thanks. I put in my "get verified" request. Must be my lucky day 'cause it says they process the requests every Sunday night.

 

[Pdizzle]

Also waiting to get verified. Hope it happens tonight

 

[tbrown4g63]

I as well am on that list. Did it friday.

 

[Spider Pig]

I'm hoping for a verify tonight. I would love to put out some mods out there

 

[believe58]

I have been reading the information offered since the beginning. This board looks very promising. I waited out the dna40 but I am going to jump on this. Time to get verified. Thank all for all the information you have offered and continue to offer.

 

[retird]

Was surfing the web and ran across this. May be of interest as you can take the information selected here and place it in the software and upload to the device as a profile . May be a good resource when wanting to use custom wires (other than Nickel 200).

NOTE: This is a "Beta Version"

TCR | Steam Engine | free vaping calculators

 

[SX_Vaper]

Lowest resistance on TC mode only goes down to 0.10ohm??


Sent from my iPhone using Tapatalk

 

[KTMRider]

Was surfing the web and ran across this. May be of interest as you can take the information selected here and place it in the software and upload to the device as a profile . May be a good resource when wanting to use custom wires (other than Nickel 200).

NOTE: This is a "Beta Version"

TCR | Steam Engine | free vaping calculators

Bookmarked. Thanks!!!

 

[LiveLongAndV'ape]

Lowest resistance on TC mode only goes down to 0.10ohm??

You can toggle the ohms lower I think

 

[KTMRider]

You can toggle the ohms lower I think

I think that's a limit of the chip, not a software setting.

 

[Mad Scientist]

Lowest resistance on TC mode only goes down to 0.10ohm??


Sent from my iPhone using Tapatalk

Might still fire lower. My DNA 40 (VS rDNA 40) also says .10 ohm minimum but it will fire at least as low as .06 (and maybe lower -- haven't tried any lower). It does seem to get "warm" when I do that though. I don't know if it's a bug or if they changed the specs along the way in one of the revisions.

 

[Nomoreash]

It's not a bug it's the soft limiting feature implemented in the DNA 40. The "Ohms To Low" error message explains how it works about 1/2 way down the page.

http://evolvapor.com/datasheet/dna40.pdf

 

[Mad Scientist]

It's not a bug it's the soft limiting feature implemented in the DNA 40. The "Ohms To Low" error message explains how it works about 1/2 way down the page.

http://evolvapor.com/datasheet/dna40.pdf

The revision I have is definitely different from the manual page (at least down to 0.06 ohm). It does not display any error message and seems to fire as expected.

 

[Spirometry]

Information:

Another software feature (General Tab) with the DNA200 we haven't mentioned (remember.. still beta... subject to change) is what I would call "Profiles" (actual names still to be decided). A number of them can be set up in the software and uploaded to the device. Changes can be made in the software and in the device.

Example of a possible profile:
Switching tanks from one to another.
You could set up a "Profile" for each tank and as you switch just select the appropriate "profile".

What to include in the profile? You decide.

Want to select coil material? Want to set the TCR (custom) ? Want to set the temp and wattage ? Want to set the preheat level, punch, duration? Want to lock the ohms?

Again preface this info as beta in nature.... (this explanation may not be as precise and as detailed as someone else may say but is just the best effort offered at this time....)

Quick one set up:

Coil Material: Nickel 200
Preheat Power: 75 watts
Preheat Punch: slider set to 5
Preheat Time Limit: 1 second
Power: 20 watts
Temperature Setting: 430F
Ohm’s Lock: not set
Profile Theme (name): Atlantis OCC
Custom Screen: default (no screen desired)

Does preheat work work with Kanthal?

 

[BlueridgeDog]

Does preheat work work with Kanthal?

No way it can as it has no idea what the temp is.

 

[retird]

Does preheat work work with Kanthal?

Preheat works in Temperature mode...

 

[AtmizrOpin]

On the DNA 200, what does preheat punch do or mean. Is that how hard it hits the coil as in watts? What exactly can you adjust concerning the preheat function?