DNA 200 Watt

[retird]

That's exactly what I used to have, until at some point the "watts" setting showed up, and I figured that was the proper way to go. See you on the Evolv forum. Thanks!

Yep... see ya over there....... I'm in many vaping forums and over the years learned that it is a community... most folks just want to help.... I don't post as much as I used to but read more.

 

[Mactavish]

Yep... see ya over there....... I'm in many vaping forums and over the years learned that it is a community... most folks just want to help.... I don't post as much as I used to but read more.

Perhaps you can pass on some of your READING skills to the newcomers!

 

[Eskie]

I created a Material and called it "Kanthal" and unchecked Temperature Sensing. Then added Watts back to the Material on device. I vape Kanthal with the Material "Kanthal".

View attachment 586597

And my Profile looks like this:
View attachment 586599

Thank you! That was one tiny annoyance I had, and did not even consider there might be a simple solution.

 

[dwcraig1]

So having "Watts" on the mod may be undesirable? Is having it in EScribe OK. I had it in EScribe but not on any mods.

 

[retird]

So having "Watts" on the mod may be undesirable? Is having it in EScribe OK. I had it in EScribe but not on any mods.

Still pondering about Watts.... I put it back on the Device but don't use it in a profile... I tried it with Watts just listed as a Material in EScribe and with Watts back on the Device and without using it in a profile I noticed no difference.

 

[KTMRider]

The latest 1.2 sp3 seems to be working on my VS DNA200. Full 2a charging.

 

[retird]

The latest 1.2 sp3 seems to be working on my VS DNA200. Full 2a charging.

Good for you KTM..... enjoy....

 

[Phone Guy]

The latest 1.2 sp3 seems to be working on my VS DNA200. Full 2a charging.

I want to order the Vaporshark dna133 flask. Only because it has the 2a charger.

Hopefully they'll (vaporshark) will have a f'ing sale! That's all I'm waiting for.

 

[Tpat591]

The latest 1.2 sp3 seems to be working on my VS DNA200. Full 2a charging.

Evolv took care of that PDQ! Gad to hear it worked out!

 

[Mactavish]

Well, a software bug, who wooda thunk it.
SP3 seems to have fixed the bug, 2 amp charging now working again on Vaporshark DNA200. Will be monitoring the charges, hope that's the end of it. VAPIN ON!

 

[KTMRider]

Evolv took care of that PDQ! Gad to hear it worked out!

Less than 12 hrs from finding the bug to fixing it. Not bad.

 

[retird]

Less than 12 hrs from finding the bug to fixing it. Not bad.

Yep I guess electrical noise can cause confusion and coding can fix it... at least they nailed it in short order it look like...and I didn't know there was two variants of the VS200 board....

I still am pondering why this didn't show up on the VS133's as they use the 200 boards?

 

[Icemanxxxv]

Rut Ro just installed the new service pack on my EMR+ S/N 030 and it wiped out my battery status. It was fully charged now the battery indicator shows empty but device manager has it at fully charged.

 

[dwcraig1]

Rut Ro just installed the new service pack on my EMR+ S/N 030 and it wiped out my battery status. It was fully charged now the battery indicator shows empty but device manager has it at fully charged.

Sounds normal enough, either upload settings or soft reboot should put it back in order.

 

[Icemanxxxv]

Rut Ro just installed the new service pack on my EMR+ S/N 030 and it wiped out my battery status. It was fully charged now the battery indicator shows empty but device manager has it at fully charged.

Soft Reboot brought it back!

 

[Icemanxxxv]

Dumb question how do I change charge current limit It is set at .5 amps now.

 

[OhTheAgony]

Dumb question how do I change charge current limit It is set at .5 amps now.

Not sure which current you're referring to (there's the max continuous input current and max pulse input current), but just change the value and upload settings to mod.

edit: oh wait, I missed charge-current. Not sure if you can set that.

Could it be you're charging it with something that isn't capable of doing more than 0,5amp?

 

[retird]

The DNA 200 has a built in 1A USB charger. It automatically detects the type of USB power supply it is connected to, so it can be plugged into standard PC USB ports or higher power chargers. The max charge current is based on the cell capacity as programmed in EScribe.

 

[BillW50]

Device Monitor
Diagnostics (button)
Set USB Current Limit (menu)

 

[Phone Guy]

To clarify, that won't give a regular "old" dna200 board the ability to charge any faster than 1A.