DNA 250 TC help

[Outcast]

I can't get this dam coil to come up to temp any tips


Sent from my iPhone using Tapatalk

 

[Outcast]

Better pic


Sent from my iPhone using Tapatalk

 

[APathos]

Kinda looks like you have max set to 64W, and your pre-heat max watts to ~75W or so? Not enough wattage. My dna250 is set to 170W/170W.

 

[Eskie]

What's the build? clearly 64W is not enough to reach temp. But what is it on what tank?

 

[Outcast]

Dual Clapton coil's 26/30 at .25


Sent from my iPhone using Tapatalk

 

[Outcast]

Mine is 166 2 cell


Sent from my iPhone using Tapatalk

 

[Eskie]

Dual Clapton coil's 26/30


Sent from my iPhone using Tapatalk

What atty are they in? I've used dual Claptons of just about that rating, they came in at ~0.2 ohm. Took a 100W preheat then 40W to maintain the temp at 450(?). And why so high to 510F? That's a hot vape. Is that how you usually vape that hot?

 

[Outcast]

Must be I just throw in some 26 parallel build bumped stuff up seems to be fine


Sent from my iPhone using Tapatalk

 

[Outcast]

What atty are they in? I've used dual Claptons of just about that rating, they came in at ~0.2 ohm. Took a 100W preheat then 40W to maintain the temp at 450(?). And why so high to 510F? That's a hot vape. Is that how you usually vape that hot?

Trying to show better on the lines in the pic I vape 440-450 but can't get over 400 it's in a coilART mage rda


Sent from my iPhone using Tapatalk

 

[Eskie]

Trying to show better on the lines in the pic I vape 440-450 but can't get over 400 it's in a coilART mage rda


Sent from my iPhone using Tapatalk

Oh, so you were shooting for 450F but only getting to ~410F. Yup, bump up the power, mostly in the preheat. Once the coil is at temp it takes a lot lower current to keep it there.

 

[Outcast]

Oh, so you were shooting for 450F but only getting to ~410F. Yup, bump up the power, mostly in the preheat. Once the coil is at temp it takes a lot lower current to keep it there.

Claps in only about 300

Sent from my iPhone using Tapatalk

 

[Outcast]

Sent from my iPhone using Tapatalk

 

[Outcast]

Sent from my iPhone using Tapatalk

 

[Eskie]

That Steam Engine curve looks exactly like the generic 316 curve from Evolv. Maybe it's corrupted? IDK. @Wingsfan0310 has several config files for a DNA and maybe he has something. I would be tempted to do a reset on your mod, use the generic 316L materials selection, and see what those graphs are like. There's no way you shouldn't be getting to temp with that build.

 

[Outcast]

That Steam Engine curve looks exactly like the generic 316 curve from Evolv. Maybe it's corrupted? IDK. @Wingsfan0310 has several config files for a DNA and maybe he has something. I would be tempted to do a reset on your mod, use the generic 316L materials selection, and see what those graphs are like. There's no way you shouldn't be getting to temp with that build.

I'm using his full mod profile


Sent from my iPhone using Tapatalk

 

[Eskie]

I'm using his full mod profile


Sent from my iPhone using Tapatalk

Then it's his fault.

Serious, you shouldn't have a problem getting those warmed up. If you open atomizer analyzer, is your resistance stable on that?

 

[Outcast]

I'm using his full mod profile


Sent from my iPhone using Tapatalk

Ok I have the factory files saved I will see what it dose


Sent from my iPhone using Tapatalk

 

[Outcast]

Factory

Sent from my iPhone using Tapatalk

 

[Outcast]

Sent from my iPhone using Tapatalk

 

[mongo74]

Is it possible you undertightened the legs? Or maybe overtightened and crushed them?

Also, before you started vaping TC, did you check for hotspots in power mode?