DNA Question

[Caterpiller]

I've only recently moved over to TC (about a month now) and have a quick question.

Why does my DNA200 never ask me "New Coil Y/N?".

It's only done this once in a month.

I switch out between a Perti dotmod v1.5 RDA and a Petri dotmod v2 RDA about once every four days, and am always expecting to see the new coil question, but it never appears?

Yes the coils I'm switching between tend to be the same build, but still I was expecting the DNA200 to be able to sence the minor differences.

Any ideas?

 

[QcVaper]

I didn't do much tc but what i'd say is : have you tried to just remove and re attach the atomiser ? Sometimes that happened to me too but i just removed it and re-attach it or just turn the mod from watts to tc , or turn it off then on. Usually any of these works for me.

 

[Caterpiller]

Thanks @QcVaper

I've tried taking the atty off and putting it back on multiple times, and switching bergen the two RDA'S multiple times and it doesn't have any effect.

Haven't tried putting it in Power Mode and switching back to TC mode.... Wait... No that doesn't do it either?

 

[SteelDriver]

Chip checks ohms. That's why they tell you it's better not to lock ohms like other chips. Taking atomizer on off should make it ask.

Sent from my SAMSUNG-SM-N910A using Tapatalk

 

[Marc411]

Agreed^^^

Personally I hit the fire button with the tank off to clear any memory that might be stored than add the new topper. So far it has worked.

 

[Dubminer]

I've only recently moved over to TC (about a month now) and have a quick question.

Why does my DNA200 never ask me "New Coil Y/N?".

It's only done this once in a month.

I switch out between a Perti Dotmod v1.5 RDA and a Petri Dotmod v2 RDA about once every four days, and am always expecting to see the new coil question, but it never appears?

Yes the coils I'm switching between tend to be the same build, but still I was expecting the DNA200 to be able to sence the minor differences.

Any ideas?

I think the default setting in Escribe is 25% so if there is not more than that difference between the new and old coils ohms it will not ask you if it is a new coil.You can change the percentage if you wish in Escribe, but there is no point that i can see.

 

[Caterpiller]

OK thanks for the feedback.

Seems I'm not getting the new coil question when others are, which is slightly irritating, but it's not causing any real issue so I'll try to ignore it.

 

[IMFire3605]

I've only recently moved over to TC (about a month now) and have a quick question.

Why does my DNA200 never ask me "New Coil Y/N?".

It's only done this once in a month.

I switch out between a Perti Dotmod v1.5 RDA and a Petri Dotmod v2 RDA about once every four days, and am always expecting to see the new coil question, but it never appears?

Yes the coils I'm switching between tend to be the same build, but still I was expecting the DNA200 to be able to sence the minor differences.

Any ideas?

A lot of mods to reset the reading you have to remove the tank/dripper, then press the fire button on the mod to get a "No Atomizer or Check Atomizer" error, then replace the tank/dripper and fire again, the mod should ask the "New Atomizer Y/N" prompt again then, this happens on my Kanger TC capable mods, my Joyetech TC mods not so much, have to go into a menu with those and specifically select lock resistance, my DNA75 doesn't ask the question unless I error out the atomizer reading and put on a low enough resistance coil to match what a TC should be before I get the prompt, though most my TC builds on my DNA75 I always plug the mod into Escribe and fine tune the settings there per build.