Does Kanger T3 fit on eVic?

[HyperRealist]

Or does it need an adapter like Vamo? BTW, eVic needs its own thread.

 

[crxess]

Direct fit

 

[daventura]

Using one right this minute.

Although they recommend removing the top cap so you don't unscrew the bottom from the body on the Kanger, and end up with a lap of nicquid.

Hasn't happened to me yet, but I screw the bottom on pretty tight.

 

[niterider]

Using one right this minute.

Although they recommend removing the top cap so you don't unscrew the bottom from the body on the Kanger, and end up with a lap of nicquid.

Hasn't happened to me yet, but I screw the bottom on pretty tight.

LOl, this happened to me yesterday. What a mess! And I knew better too but I was in a hurry.

 

[worthatry]

Using one right this minute.

Although they recommend removing the top cap so you don't unscrew the bottom from the body on the Kanger, and end up with a lap of nicquid.

Hasn't happened to me yet, but I screw the bottom on pretty tight.

I have had this happen twice. I like my Evic but my only complaint comes from the MT3s. I have 2 and some spare bottoms and I have had 2 stop being read by the Evic. They worked at first then just stopped getting read. I have tried to pull the pin on the MT3s but it either doesn't work or I don't know what I am doing. I am guessing the latter but still I shouldn't have to rig something to work. I just use them on my twist now and use novas on the Evic.

 

[niterider]

I have had this happen twice. I like my Evic but my only complaint comes from the MT3s. I have 2 and some spare bottoms and I have had 2 stop being read by the Evic. They worked at first then just stopped getting read. I have tried to pull the pin on the MT3s but it either doesn't work or I don't know what I am doing. I am guessing the latter but still I shouldn't have to rig something to work. I just use them on my twist now and use novas on the Evic.

The issue is with the heads and not the eVic. there was a run on the heads that effected an entire batch. A simple pull with some pliers just slightly should do the trick so I'm not exactly sure what you're doing wrong. I agree, it is annoying when that happens.

 

[crxess]

Anyone want to guess why the bottom comes unscrewed on the kanger on an eVic?

It isn't the eVic causing this.

If the Kanger center pin is high it is possible to tighten it flush down on the eVic. The base now has additional pressure holding it in place. The nice thing is eVic unlike most mods HAS a removable cone.

 

[worthatry]

The issue is with the heads and not the eVic. there was a run on the heads that effected an entire batch. A simple pull with some pliers just slightly should do the trick so I'm not exactly sure what you're doing wrong. I agree, it is annoying when that happens.

I was trying to use a screwdriver or tweezers and just pull around it but couldn't get it to read again. I even pulled the center pin out and put it back in, no luck. I may have to find a video on how to do it but I just adapted and used my twist for those. I have several novas and mini novas to use with my Evic and I do like the Evic and don't really blame it for the MT3s problem but it just affects me with the Evic.

 

[speedjason86]

I think I heard somewhere that the ego threading on the eVic is not deep enough for the kanger clearos.

 

[crxess]

I think I heard somewhere that the ego threading on the eVic is not deep enough for the kanger clearos.

Rumor abound
Having said that, I own 2 eVic and have about 35 Kangers. They do work on the eVic just fine.

 

[jfountain2]

They fit on mine with no problems and work great. I agree you have to remember to take the top ring off the eVic before removing the T3 or you will end up with juice all over the place.

eVic with top removed and Kanger T3




eVic with Kanger T3 ready to vape