does size matter?
- Thread starter retired2020
- Start date
- th_trl_thread_readers 0
-
- Tags
- size
- Status
To Me, Less is More. My Favorite set-up is a Tesla T40w with a Bubbled GEAR RTA on top.
Got one on a Small Belt Pouch right now because I'm getting ready to take the Cans/Bottles back. And then a trip to Home Depot.
My D2D set-up is a Wismec Surface Squonk Mod with a NarDa RDA on top. This Set-up is a about the Smallest Regulated Squonk/RDA set-up I know of. And it is a Flavor Machine.
Got one on a Small Belt Pouch right now because I'm getting ready to take the Cans/Bottles back. And then a trip to Home Depot.
My D2D set-up is a Wismec Surface Squonk Mod with a NarDa RDA on top. This Set-up is a about the Smallest Regulated Squonk/RDA set-up I know of. And it is a Flavor Machine.
@retired2020, not necessarily.
I do like Taifun GT IV clones with a SS 316L coil, 5 spaced wraps of 0.8mm × 0.2 flat wire at around 0.4 ohms. A nice warm but incredibly cloudy vape.
For an RDA I quite like Cuthulu Mods Mjolinir with 6 wraps of 0.4mm SS 316L round wire at around 0.5, when wicked right it's really nice for flavour.
And as for mods, it's all depends on the resistance. The lower I go, the larger I tend to need so that I can make sure there's plenty of runtime.
I do like Taifun GT IV clones with a SS 316L coil, 5 spaced wraps of 0.8mm × 0.2 flat wire at around 0.4 ohms. A nice warm but incredibly cloudy vape.
For an RDA I quite like Cuthulu Mods Mjolinir with 6 wraps of 0.4mm SS 316L round wire at around 0.5, when wicked right it's really nice for flavour.
And as for mods, it's all depends on the resistance. The lower I go, the larger I tend to need so that I can make sure there's plenty of runtime.
Might not be a shower, but a grower.
Sometimes the little guys can do other things alil better....like this little guy. Lol
Attachments
Which RTA(s)? Didn't leak before but started leaking recently? What are the "taller older" RTAs?
I claim that title tooMight not be a shower, but a grower
It's mainly how you use it...............
.......what I mean is, if you were to put that tall tank on a side-by-side mod, it's size may not bother you much.
I have a lot of tall 22mm tanks and I'm used to them. The 24-25mm tanks of the same capacity aren't that much shorter anyhow. The only time I notice the difference is on a 2ml tank but then you have that 2ml problem.
.......what I mean is, if you were to put that tall tank on a side-by-side mod, it's size may not bother you much.
I have a lot of tall 22mm tanks and I'm used to them. The 24-25mm tanks of the same capacity aren't that much shorter anyhow. The only time I notice the difference is on a 2ml tank but then you have that 2ml problem.
Oh (and just for fun) my friend used to say "it's not the size of the wand... it's the magician that matters"
I tend to like bigger build decks because they're easier to build on. Anything smaller than 25 mm needs to have only two posts. I don't care for the older 22 mm decks with 3 or 4 posts.
my little rta now is leaking sometimes after loving them for 4-6 months.went back to the taller older rtas for now.first day now and it feels like i'm back with a 100 and want a filter king.
When I first started with RTAs, it was short 22-24mm MTL/RDL attys. I loved having a low profile setup.
I completely snobbed tall RTAs for the next 2 years, and side-stepped into squonking.
Eventually, a low profile Gear RTA brought me back to the land of RTAs.
A side-by-side Mixx mod threw the door wide open, and now I have 5 really tall RTAs sitting on Mixx mods.
the gear and never before, have it penciled in for repair in September. got use to the size,all my rta's are bigger.don't want to give a laundry list of rta's.
football season is coming along with cooler temps,not so lost that can't be found again.
Do you have tips that extend? Asking for a friend.Might not be a shower, but a grower
That looks lovely. I'll take 2. For my friend, of course.A pink Provari extention cap?
- Status
Similar threads
- Locked
- Locked
- Locked
