- Status
SUUH WEET... Just ordered these tonight, without seeing this thread...and it sounds like I'm in for a pleasant surprise! I've been dripping since day one but tonight I said WTH and tried one of the 5 cartomizers that came with my RoughStack...the thing actually freakin rocks! I've been kinda getting tired of the contant dripping believe it or not...and boy, I really can't believe how well these stock cartomizers work. So I can't imagine how these E2s will work. The one caveat, the OP says they need to be syringe fed...I didn't know that - but just read about it in the fine print 
I may try to add that to my order right quick since it's only been about an hour. Everything is from MV, btw.
HAPPY vaping WORLD OF ECF!!
ice
I may try to add that to my order right quick since it's only been about an hour. Everything is from MV, btw.HAPPY vaping WORLD OF ECF!!
ice
Thanks Jonny, wish I'd seen that, just ordered 20 of the cheap 3ml syringes for the E2 clear tube mod, they work GREAT without any glue or washers, just cut and push on. I'll stock up when i order more of the syringes, just ordered the XL's from COVJonnyVapΣ;2213667 said:
Hey guys you really don't need a syringe, in fact what you do to make this quite easy is pull off the soft tip on top, pull out the next silicone O ring, then carefully pinch the Oring covering the ceramic cup against the wall and pry up to get that one off. Now you can fill by just dripping in these until full and just place the one small O ring back on to cover the ceramic cup, I find mine even run better this way. Only thing I don't like about these is they dont' give a big TH but the vapor is very smooth
mwa's right, i cut all my syringes up weeks ago to put on cut E2's for a see-through, but you do need some good dental like picks to get the last filler ring out of the E2.
I may have to try that. So far the first few pulls off the carto is great then anything after that is burned. Filled two cartos last night with two different juices and both have the same result. May have to make a special PG only bottle up tonight since the 60/40 blend is not wicking fast enough for the way I vape...which is almost constant...lol
Yikes...looks like I stepped up a few ranks ordering these...LOL...I'm going to have to get in touch with you all when these arrive. Didn't realize there was some skill involved.
ice
ice
Guys I do run a pretty heavy VG mix in mine, trick seems to be also tilting you PV and making sure the wicks are getting wet to get a good vape, play around a little trying to set and tilt your PV a bit to see what works for ya, the wicks cant keep up with chain vaping on these things like some of us like to do (me) I'm like a Loco motive freight train vaping down the tracks so I keep like 2 of these filled with different flavors while also having another couple of PV's set up and enjoy rotating between about 6-7 different PV's at a time, but these are good for going out and about too, take a few vapes put it down, come back to it a few minutes later and hit it again a few times put it down, as far as getting the Oring off the ceramic cup I just use a long pair of pointy straight tweezers and pry the O ring to the side kind of pinching it and prying up at the same time and once you feel it break loose your cool to pry up the rest of the way, then I put the small one back in just so I don't leak when I set my PV down. They sure are a different kind of vape though, very smooth and no filler in your carto is quite different
I have just been filling a 10 mil syringe every morning and using a drip tip on top of mine. When it's empty (usually about 2 hours) I just pop off the drip tip stick the syringe in the holes and shoot em up. The whole process with a syringe seems daunting but if you just keep a filled one sitting around it really takes about 15 seconds.
You can surely go that route if you like using the syringe, I just would rather drip right out of the bottle down the side of the carto, I also get much better performance out of these it seems with the big O ring off of the ceramic Cup
Doesn't that allow the juice to leak out of the reservoir tho? I'm sure ill wind up giving it a shot anyway, but sometimes I like to lay on the couch in the evenings and watch a movie etc. It just seems like without the ring in there there's nothing to keep the juice where it belongs?
Been vapin E2 R4 XL's for better than three weeks. And the 3.0 ohm two weeks. All mine are from CoV, (Clouds of Vapor). All my juice starts at 50/50. I've had no primer in any of these from CoV. I found early on I can easily out vape their wick. Tried cutting my juice with PGA, went too far. Makes for a faster wick, VERY HOT vape. Went back to 50/50, but loaded two cartos, on two different color batts. Switch back and forth between the two as soon as I detect a change in the vape. Allows greater dwell time for wick to catch up. I'm seeing very little difference between 2.6 & 3.0. on eGo/Riva, on ProVape-1, and on Lil Sister. My experience so far. . .these things tend to vape warm. When the wicking is right they're outrageous vapor producers. Every now and then I get a liquid drop out the carto mouthpiece hole. Haven't determined what's causing this yet, just dab with issue after taking a hit if the small bead of juice is there. May have something to do with vapor condensing in the tube on the way out. I don't mind using a syringe to fill. So far I like um better than any other carto I"ve used.
Cheers,
otrpu
Cheers,
otrpu
Syringing through the fill holes in my experience is much faster and to me, easier that droppign into filler and waiting for the soack, etc...
I love keeping the filler ring in there if at all possible. You CAN have problems it its not there with stuff leaking into the cup and when it is reseated properly (or if you were lucky enuf to have a dry carto when it arrived and didn't need to remove the filler ring for a rinse) it makes it more efficient to fill...you get a visiaul indication that you are full when juice bubbles out the other hole... and then of course you can lay it horzontal with no problem...
- Status
