eGo ONE tank series – CLR coil

[pufZeppelin]

Super bad gurgling and spit back with stock CL coils. Gonna have to wait for CLRs. No leakage/seepage though

•dry hit means there is NOT enuff juice
•gurgle means there is TOO MUCH juice

simply clear it out...

gurgle MIGHT happen because power too low to burn off the excess juice / ratio of air flow to power (a TIGHT air-flow will draw MORE juice into wick)


a Remedy:

 

[oplholik]

Finally got a black ego one mega for my B/R Provari Classic.

 

[MikeADore]

Finally got a black ego one mega for my B/R Provari Classic.

View attachment 610529

I think the black eGo One is the classiest looking atty in my collection. Looks great on that black Provari, too.

 

[pufZeppelin]

Finally got a black ego one mega for my B/R Provari Classic.

looks sweet... !

maybe could use a red drip tip

- Acrylic Bullets
- Transparent Jerrycan Wide Bore

 

[oplholik]

It does look pretty good I think. I'll get it all cleaned up tomorrow and put it to work.
Thanks @pufZeppelin for fixing the pic. My iPhone recently started doing that. It looks correct until I upload it to a post, then it goes sideways for some reason.
Red drip tip? Gonna get a couple on my next FT order.

 

[Mohid]

•dry hit means there is NOT enuff juice
•gurgle means there is TOO MUCH juice

simply clear it out...

View attachment 610457

gurgle MIGHT happen because power too low to burn off the excess juice / ratio of air flow to power (a TIGHT air-flow will draw MORE juice into wick)


a Remedy:

I didn't all except the music
I always clean excess juice from the coil every time I refill. But it pulls up excess juice every time it put it down for a few minutes. And gurgling does disappear when I vape it at 5v on istick. But the EGO one battery doesn't supply that much voltage and gurgling never stops.

PS: I use voltage on the iStick because ohm reading is sometimes jumpy on this thing despite tightening of coils and everything. I've previously gotten a nasty hit when I was at 14 watts on 1.5ohm coil and it jumped to 2.3ohm somehow. Had to change the coil.

 

[oplholik]

looks sweet... !

maybe could use a red drip tip

- Acrylic Bullets
- Transparent Jerrycan Wide Bore

View attachment 610553​

I like the Jerry Cans. Do you have any? I was going to order some then I saw this. " Designed for Joye 510 atomizer. Can fit most atomizer or cartomizers which diameter is 9.2mm(0.36in) or so."
Most of my atties, including the ego one, measures about 8.7mm.

 

[oplholik]

This is a little better.

 

[pufZeppelin]

This is a little better.

there ya go, that's lookin good


** no tricks - just put pic in , it stays upright ??

 

[Katdarling]

Finally got a black ego one mega for my B/R Provari Classic.

View attachment 610705

Yumm!

This is a little better.

View attachment 610711

Mega YUMM!

 

[FranC]

 

[Nanny22]

 

[FranC]

Morning,Nanny

 

[Dieseler]

I didn't all except the music
I always clean excess juice from the coil every time I refill. But it pulls up excess juice every time it put it down for a few minutes. And gurgling does disappear when I vape it at 5v on istick. But the EGO one battery doesn't supply that much voltage and gurgling never stops.

PS: I use voltage on the iStick because ohm reading is sometimes jumpy on this thing despite tightening of coils and everything. I've previously gotten a nasty hit when I was at 14 watts on 1.5ohm coil and it jumped to 2.3ohm somehow. Had to change the coil.

Are you using the cl heads.
Also the ohm should not jump like that as well it may go up a 1 tenth or so from 1.5 to 1.6 or 1.7 then it
should settle in until the coil starts to gunk up and ohm's tends to rise some.
But never jump as much as yours did.

Reason i ask is when i was using the cl coils they were always a hit or miss some heads gave burnt taste right off the bat and some lasted for a while never knew when screwing on a new one what
would it be like and always did pre juice the cotton .

The clr coils on the other hand i have no problems with gurgling, dry hits, etc when new or when i re-build.
them.

If your using the clr coil head let us know as then the build is not proper.

 

[pufZeppelin]

lots of sales going on, hope all the peeps find what they might want...

 

[FranC]

Oh my. I won a Freemax Starre tank

 

[pufZeppelin]

Oh my. I won a Freemax Starre tank

well that's very cool !

big tank, big air - thinking: do those use the aspire style atlantis/triton coils ?

 

[FranC]

Don't know but an RBA is available for it.

 

[Mohid]

Are you using the cl heads.
Also the ohm should not jump like that as well it may go up a 1 tenth or so from 1.5 to 1.6 or 1.7 then it
should settle in until the coil starts to gunk up and ohm's tends to rise some.
But never jump as much as yours did.

Reason i ask is when i was using the cl coils they were always a hit or miss some heads gave burnt taste right off the bat and some lasted for a while never knew when screwing on a new one what
would it be like and always did pre juice the cotton .

The clr coils on the other hand i have no problems with gurgling, dry hits, etc when new or when i re-build.
them.

If your using the clr coil head let us know as then the build is not proper.

That was a GS Air coil and not rebuilt. It was the second day in use.
I believe it was defective and because it's dual coil maybe one of the coils was misbehaving.

Congratulation @FranC

 

[Dieseler]

That was a GS Air coil and not rebuilt. It was the second day in use.
I believe it was defective and because it's dual coil maybe one of the coils was misbehaving.

Congratulation @FranC

Gotcha