eGo-T Vs Go-go

[Erfmann]

I know the current topic in this thread is the post issue but I wanted to come back and comment on something that Erfmann said in a post about a nice tip to replace the plastic plug on the Go-Go. He used a Ego-T tank cut it down and put it right on the Go-Go Cart. Well, I would like to report that I have also tested this and it is working perfectly. I measured about 10mm from the edge (the part that would normally rest on the top of the Ego-T atomizer "1st Gen") and cut off the rest. It fits snuggly and the lip rests on the lip of the Go Go Cart. The draw is tighter now, though I do want to report I got the best draw by removing the 2 small plastic pieces on the mount piece. So, I would like to thank Erfmann for the recommendation and let anyone else know who has an Ego-T 1st gen tank that this method works perfectly if you are looking for a nice mouth piece.

Thanks

Hey sand, glad it's working out for you....you going to come to the meetup this Sunday? Should be good times... Hope you can make it...

 

[alongo]

I know the current topic in this thread is the post issue but I wanted to come back and comment on something that Erfmann said in a post about a nice tip to replace the plastic plug on the Go-Go. He used a Ego-T Tank cut it down and put it right on the Go-Go Cart. Well, I would like to report that I have also tested this and it is working perfectly. I measured about 10mm from the edge (the part that would normally rest on the top of the Ego-T atomizer "1st Gen") and cut off the rest. It fits snuggly and the lip rests on the lip of the Go Go Cart. The draw is tighter now, though I do want to report I got the best draw by removing the 2 small plastic pieces on the mount piece. So, I would like to thank Erfmann for the recommendation and let anyone else know who has an Ego-T 1st gen tank that this method works perfectly if you are looking for a nice mouth piece.

Thanks

Hey guys, when you use the ego-t mouthpiece you are only drawing thru the two slots on the side , take a drill bit and drill a few hole in the bottom thru the guts of the thing then it is straight thru and awesome, Al

 

[Sandfury]

Erfmann, I plan on being there. I am also dragging along a buddy of mine that I am working on getting into vaping.

 

[Sandfury]

Here is a picture of my modified Ego-T Tank. Hope that helps.

 

[leenix]

thanks scooter.

Funny you should mention the chocomint tx i saw your endorsement of the juice on another thread and ordered a bottle of that too to help justify the priority shipping cahrge when i ordered my prefilleds. went with the ry4 on the prefilleds and will share what i think of it.

Has anyone gotten the 'snap crackle pop' thing with gocarts? I used boge 510 cartos before GoGo and i just loved that crackle of a fresh carto with them.

thanks all.

GoGo!!

 

[Panhandler]

This gogo user is having carto problems.....I'm not much help.
Anybody want to help him.
http://www.e-cigarette-forum.com/forum/new-members-forum/179536-gogo-carto-problem.html

 

[george01]

The GoGo user can post here now, Thanks a lot Panhandler
Hello,
looks like i am the only one who have Problems with the Cartos.
They are still filled good but dont wick and taste burnt.
My Juice is 80/20.

george

 

[ancient puffer]

I just wanted to let you all know that I received a PM from SSV2 (he didn't say his real name) stating that someone alerted him to my post and the ensuing discussion about CE's customer support. He said that in February he began as a temporary employee for CE, to help while they sort out some personal issues. Apparently there is a thread in CE's forum explaining the situation, and asking folks to email him directly with customer service issues.

He asked me to email him directly, which I've done. I'll keep you all posted, but it looks to me like a genuine effort to make things right. I'm not sure why the contact email on the web site isn't forwarded to SSV2 in the first place, so that this sort of thing could be avoided. But like I said it sounds like they're trying to get things squared away.

I was going to post SSV2's email here but I don't know if that's appropriate. I would urge any of you who needs to contact CE to send him a PM or look for his thread in CigEasy's forum below.

Cheers!

Thanks for sharing this, SG. I think we all need to realize that the "approved vendors" here aren't trying to rip anyone off. This is a relatively new product, and its naturally going thru some growing pains, not the least because most of the equipment is being manufactured in China. These vendors are, to a great extent, dependent on their suppliers, but they seem, to me, to be doing the best they can to keep up with the demand and still provide us the support we expect.

Keep us posted

 

[txtumbleweed]

The GoGo user can post here now, Thanks a lot Panhandler
Hello,
looks like i am the only one who have Problems with the Cartos.
They are still filled good but dont wick and taste burnt.
My Juice is 80/20.

george

Have you tried a different juice? I've read every post on the Go-Go since they came out and I don't remember any getting burnt taste except when they intentionally ran them dry. What flavor of juice are you using?

 

[Ceegary]

Got me stumped, I haven't had any that failed to wick and get constant vapes. Sounds like you're filling it right. With your syringe, are you starting at the bottom and then pulling it up gradually, then topping off the top of the filler? Does not make sense that is happening to all your cartos, logic says it's something you're doing, but I can't figure what.

I ran one carto too dry and got a burnt taste. Opened it up and sure enough it was burnt on both the filler and center wrap. I cut those parts out, rewrapped it around a q-tip and then re-inserted, I also left a small piece of q-tip tube in to extend the center-tube. Have yet to try it out.

 

[binaryman]

Some flavors have a burnt taste regardless of device. I ran across that with my DIY exploits, where coffee and cappucino just didn't cut it for me.

 

[madmach]

if you were playing around when you first started pushing the button with the cartridge on, then you will get the burnt taste.

 

[george01]

I cut one, there is enough juice in the filler, but almost no wick on the centertube. also when i let it sit for 10 min, Taste and Smoke again like new.
3 to 5 Puffs later everything is gone.
When its working, i have to say its awesome, Taste great, lots of Vapor

 

[scootertramp]

I cut one, there is enough juice in the filler, but almost no wick on the centertube. also when i let it sit for 10 min, Taste and Smoke again like new.
3 to 5 Puffs later everything is gone.
When its working, i have to say its awesome, Taste great, lots of Vapor

Below my signature is the guild book link. It will help you

 

[madmach]

it sounds like there is more vg than pg the more vg the longer it will take to wick as a rule there is some thin vg juice out there. i have had mine 1 kit for 7 weeks and the other kit for 6 weeks had issues with the charger a few of the lr cart,s.i just fill them let them sit for a little while than use them but the type of juice you use has a lot to do with the wicking of these things.i use 80%pg-20%vg or 70%pg-30%vg both seem to work good but the 70-30 takes a little bit longer to soak down to the bottom.

 

[scootertramp]

I cut one, there is enough juice in the filler, but almost no wick on the centertube. also when i let it sit for 10 min, Taste and Smoke again like new.
3 to 5 Puffs later everything is gone.
When its working, i have to say its awesome, Taste great, lots of Vapor

Link to guide under my signature

 

[george01]

@scootertramp, sorry did like they said, same.

@madmatch, its 80/20 i use

 

[GoAskAl]

@scootertramp, sorry did like they said, same.

@madmatch, its 80/20 i use

I've been using a 50/50 mix and using a syringe to fill them and have had no problem with any of the juices yet. Don't have a clue what could be causing the problem. Strange...

 

[scootertramp]

I've been using a 50/50 mix and using a syringe to fill them and have had no problem with any of the juices yet. Don't have a clue what could be causing the problem. Strange...

I use a multitude of mixes.
Even with 100% VG I have not had any issues that are worthy of noting.
So blends just taste better than others to me. So I play around with them until it's the flavor I like. The more VG the sweeter to me.
Everyone's taste buds are different. The hardest thing about the GoGo is finding the perfect flavors to merit having it's own Cartomizer! lol

 

[ancient puffer]

George1, how much are you vaping on it? By that I mean how often. Although I occasionally hit it twice in a row (about 3-6 seconds max). In general, I hit it about once every (at least) 30 seconds. That seems to give it plenty of time to wick. From what you describe, the juice wicks down to the atty eventually (after 10 minutes sitting idle I think you said).

I also know that regardless of PG/VG mix, some juices are MUCH thicker than others. Do you have some PG or distilled water you could thin it with to see if that helps? Just a thought.