Yeah, if you haven't caught the disease, consider yourself lucky 
EHPro Mini Buddha
- Thread starter Btsmokincat
- Start date
- th_trl_thread_readers 0
- Status
No matter how hard I try, I can't convince my wife to give up smoking for vaping.
i know your pain
i have 12 years of relationship with my gf (fiancee)... and not, she doesnt want to quit.
no matter how hard i try... last months i vape while she smokes
Another vendor that has a good price for the Mini in Spain.
Comes out cheaper if you buy from them if you are not in the US.
US vendors tend to gouge on shipping fees for international buyers !
BIG BUDDHA MINI RTA EHPRO | MASQUEVAPOR.com
Comes out cheaper if you buy from them if you are not in the US.
US vendors tend to gouge on shipping fees for international buyers !
BIG BUDDHA MINI RTA EHPRO | MASQUEVAPOR.com
No matter how hard I try, I can't convince my wife to give up smoking for vaping.
Gotcha. My wife can't vape, it makes her physically ill. And I've got friends who chain vape and chain smoke at the same time.
The iStick 30 is going to be one of my next buys too, considering how narrow the Buddha is it does seem be mismatched on the 30. Hell I might just use the Buddha on my Ego-C!
I put it on a50W istick today to see how it looked, and it looks nice. I got an 18mm Mini Nemesis for mine. I'm hoping the batteries will be here tomorrow. I've been running it on a 22mm mech.
Rebuilt mine today, and its vaping very nicely
I did 7 wraps of 27g on a 2mm. Was around 0.65 ohms, and that's a nice vape on a mech.
I did 7 wraps of 27g on a 2mm. Was around 0.65 ohms, and that's a nice vape on a mech.
I rebuilt mine today first with 26 gauge. The screw chewed through one of the leads so I switched to 24 gauge, 9 wrap, 2.4 mm at .6 ohms. It's vaping like a charm at 24 watts on my Smok M65. This little RTA wicks awesome and doesn't seem finicky at all.
Side note... decided my Lemo drop fit the istick 30 best
Side note... decided my Lemo drop fit the istick 30 best
Ah, it is 26g I used! Yes, a screw chomped the 27g one I used. I need to sand the screws.
I swear I'm getting dementia
I swear I'm getting dementia
I've been so happy with the spaced 27ga coil in my Mini Buddha, I doubt I'll change it till it falls apart. Been using it daily since I got it. It quickly became my all-day-at-work tank because it's heck of a nice vape in a stealthy package when it's sitting on an iStick. 1.1Ω @ 18 Watts, and the flavor is top notch.
Why does mine flood, tried short wick long wick, tucked under. air wide open. running at 1.8 ohm 11 w on a Istick 50
First check for a bad or missing oring. If the tank isn't completely sealed it will flood. There should be two orings at the bottom and 2 orings at the top and an oring on the top of the chimney.
If you are using a high PG thin eliquid that may require extra cotton.
all o-rings in place,use max vg it does it slowly and then end up with juice in mouth piece
i got the same problem. i just chek wick dont toch air holes in deck, this fixed a lot the problem... still i got liquid on air channels when the buddha mini is not in vertical position
besides ...when refill, i just note if i over refill the tank got flooded
like 3/4 of the tank is enough to keep an air bubble
besides ...when refill, i just note if i over refill the tank got flooded
like 3/4 of the tank is enough to keep an air bubble
Last edited:
- Status
Similar threads
- Locked
