The costs of running this huge site are paid for by ads. Please consider registering and becoming a Supporting Member for an ad-free experience. Thanks, ECF team.

Esterigon - help needed

Discussion in 'The GG' started by Moonwalker, Feb 8, 2017.

Thread Status:
Not open for further replies.
Image has been removed.
URL has been removed.
Email address has been removed.
Media has been removed.
  1. Moonwalker

    Moonwalker Ultra Member Verified Member ECF Veteran

    Apr 26, 2012
    Belgrade, Serbia
    I need a help from you good GG people. :blush:

    I would like to assemble Esterigon and parts that I have are:

    Esterigon 18350 Tube
    Esterigon Venting Cap
    Esterigon Button Case
    Esterigon AD Ring
    Esterigon O-Rings

    What else do I need? I was looking spare parts for Esterigon section in store and on Imeos spare parts list but that doesn't help a lot. It seems there are so much parts that I am not sure if I need all of them or there are some variations depending what you want to assemble.

    Of course that I don't mean different size tubes or same parts in different colour/material, but still there's really a lot of parts.

    So I would really appreciate if someone could write what do I need beside parts I already have to assemble working Esterigon.

    You can use this page where all spare parts are to write down what should I buy:

    Esterigon Spare parts - The Golden Greek Store


    Thank you. :thumbs:
     
    • Like Like x 3
  2. Moonwalker

    Moonwalker Ultra Member Verified Member ECF Veteran

    Apr 26, 2012
    Belgrade, Serbia
    No one? :tumble:
     
    • Like Like x 1
  3. Izan

    Izan Vaping Master ECF Veteran

    Jul 1, 2012
    Mallorca, Spain
    I am sitting with my spare and taking it to bits as I list this to double check I don't miss anything.

    The bottom cap is:
    Locking cap,
    venting cap,
    negative battery insulator
    and a small, fat o-ring. (my spare was marked/bagged separately.)

    Battery tube of choice.

    Button case assembly consists of 4 sub-assemblies.

    The positive contact from the battery:
    Esterigon Battery Moving Pin,
    Proteus Battery-Atomizer Spring (exists 2 times on Esterigon),
    Esterigon - Proteus Moving Pin Case (exists 2 times on Esterigon),
    Esterigon Battery Center Post,
    Esterigon Steady Pin Insulator
    And two o rings

    The button:
    Esterigon Button Head
    Esterigon Button Pin
    Esterigon Button Spring
    Esterigon Button Insulator
    and a tiny little o ring

    The top cap: Ad or non AD
    AD: Esterigon Ad Ring

    The top cap positive contacts:
    Esterigon Atomizer Moving Pin Insulator
    Esterigon - Proteus Atomizer Center Post
    Esterigon Atomizer Moving Pin
    Esterigon - Proteus Moving Pin Case (exists 2 times on Esterigon)
    Proteus Battery-Atomizer Spring (exists 2 times on Esterigon)
    Esterigon - Proteus Atomizer Insulator
    and two o rings


    Cheers
    I
     
    • Like Like x 4
  4. Moonwalker

    Moonwalker Ultra Member Verified Member ECF Veteran

    Apr 26, 2012
    Belgrade, Serbia
    Thank you, thank you very very much. Much appreciated. :thumbs:
     
    • Like Like x 3
  5. Izan

    Izan Vaping Master ECF Veteran

    Jul 1, 2012
    Mallorca, Spain
    After almost two years of daily use, the only part that has shown any wear that would impede operation, is the tiny, button o-ring. As it wears, the button becomes easier and easier to remove.

    I suggest ordering a few extra o ring kits, a few extra springs (both types) and a back up for each of the plastic disk insulators, just in case.

    Cheers
    I
    ETA: @Moonwalker , you are very welcome, I'm happy to be able to assist. :toast:
     
    • Like Like x 3
Thread Status:
Not open for further replies.

Share This Page

  1. This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
    By continuing to use this site, you are consenting to our use of cookies.
    Dismiss Notice