Hey provari owners. Will a 510 DCT tank Cartomizer work on a provari? It's dual coil 1.5ohm. Or will I get the E1 error code? I wanna run up to my store and get one if they will work! Thanks!
Fast! Will these work on Provari?
- Thread starter brockadams
- Start date
- th_trl_thread_readers 0
- Status
If you exceed the current limit you will but since the Provari is a VV you can control that. The voltage range fora 1.5 ohm will be between 3 and 4 volts. I get E1s when I go with too high a voltage. The controller thinks there is a short. You also have to worry about the E2 error if you exceed the current limit.
But, as my mother said "Don't put all your eggs into one basket". That's why I prefer to have several smaller PV and not just one big. Might be more expensive in the long run but...
That's why Provape cam out with the V2 Provari. The old ones have a 2.5amp limit and the V2 has a 3.5amp limit. The V2 works fine up to 5v. Mine will give an E-1 message at 5.3v (3.53amps) with a 1.5ohm DCC.
Last edited:
Short answer yes....more complicated answer, if your juice falls in the preference range reported by a lot of people youre looking at best flavor at 3.5 volts give or take a few either way...you'd need a .9 ohm carto or lower to really worry about one not working correctly on a V2 Provari...unless you like warm vapes in which case higher resistance is better.
So I went and got one.. It's ok. This might sound weird, but I'm looking for something that has a crackling sound.. For some reason I enjoy that! Does that make sense? What device makes that sound.
Actually I didnt see the dual coils on your setup...try it at 4.5 volts and see if it crackles.
if it was a single coil then 3.5 would be pretty close to ideal range for flavor...dual coil effectively doubles the resistance, so youre looking at 4.5ish on the volts give or take a few either way.
It turned it up to 4.5. All I'm getting from this thing is burnt dry hits.. No matter where I put it..
are they flanged or non flanged cartos. pre-punched? and how many holes are punched? i haven't had good experiences w/ smoktech flanged pre-punched cartos... The dual coil cartos i use are from healthcabin.net (healthcabin branded) and i've NEVER had a bad one.
if they're prepunched, you could try to open the holes a bit and see if that helps. if it gave you dry burnt hits from the get-go, it's probably a junk carto.
if they're prepunched, you could try to open the holes a bit and see if that helps. if it gave you dry burnt hits from the get-go, it's probably a junk carto.
They are the flanged pre-punched cartos. I'll try punching it more to see if that helps. But so far it's been nothing but nasty!
I just ordered one to go on my eGo Twist 1000 mAh. I hope it works, it should. BTW, I also ordered single coil 2.0 Ω carto's.
If it's 1.5ohms and you're running it at 4.5volts.. it's gonna be burnt and nasty. It's pretty much ruined now. If I were using a 1.5 carto.. I wouldn't go over 3.5v.. but's that's me.
I use 2.0 ohm single coil smoktech cartos with my dct tank on my lavatube and twist and they make that crackling sound. I never vape over 5 volts. And I know what you're talking about as far as "hearing it crackle" goes.
But one unrelated question: anyone else get little tiny electric shocks from their drip tips when using a Vision ViVi Nova? Every once in a while I'll feel a tiny shock from my Nova. I know it's electric (boogy oogy woogy woogy lol), because I've been shocked before (arcade game, electric fence, static discharges, etc). Why and how come?
But one unrelated question: anyone else get little tiny electric shocks from their drip tips when using a Vision ViVi Nova? Every once in a while I'll feel a tiny shock from my Nova. I know it's electric (boogy oogy woogy woogy lol), because I've been shocked before (arcade game, electric fence, static discharges, etc). Why and how come?
- Status
Similar threads
