• This forum has been archived

    If you'd like to post a thread, post it here instead!

    View Forum

Fasttech Veterans

Status
Not open for further replies.

dw117

Super Member
ECF Veteran
Jul 10, 2014
857
1,324
Kernow
What you waiting for? ;)

e-packet option at FT,£20 all in and you'll have it this time next week.

Placed an order with FT for the lemo 2 and a derringer rda clone along with some drip tips (can't place an order at FT without some drip tips!) and a skin for my rDNA 40. Didn't go for express shipping as I'm in no rush for it, probably take more time to wait for them to stock all the items in the order. Regular china post is fine.
 
  • Like
Reactions: Pictor

Pictor

Vaping Master
ECF Veteran
Verified Member
Jun 27, 2009
9,066
19,246
UK
Mine is still showing this Trish View attachment 458207
Mine showed one day yesterday, but that's gone today. I've sent a message to them asking why, and when mine will be despatched. Getting a bit fed up now as it's been more than a month.

Today.
So you'll have both posted,with a bit of luck
Not sure mine will get despatched in the next 24 hours ...but the grey one will though! :D
 
  • Like
Reactions: terry w

Davantrac

Ultra Member
ECF Veteran
Verified Member
Jun 3, 2014
1,190
1,272
Darlington, UK.
image.jpg
 

Brynglas

Vaping Master
ECF Veteran
Verified Member
Sep 22, 2014
4,561
6,449
ΩFlint MountainΩ
TBH neither, if they were like the kayfun ones with a steel chimney section I might have gone for them

If you think of the design of the subtank Bob,don't think they could have made them any other way.Top section of the chimney needs to be part of the top cap.

What`s the capacity of them george ?

Doesn't say mate.But as i said there are a large and a small version.
 
Last edited:
  • Like
Reactions: terry w

terry w

Vaping Master
ECF Veteran
Verified Member
Sep 1, 2012
8,666
10,916
Manchester UK
Finished off my PMP last night, so today i cleaned and wicked a kayfun like this chappie.

And i have filled it with some Gravity from NT, it`s now on an i-stick charging, so i will report how it performs later on. :)


*Update*

Bloody fantastic...I used to wick my old kayfuns like this, and forgot just how well they wick this way. No more sticking the tails to the block now with the juice holes exposed. I am guessing it`s the extra wicking material what makes this way so good ! I used rayon by the way, 1.6 ohms, and 12 watts, on a fully charged i-stick. :thumbs:
 
  • Like
Reactions: Pictor

Pictor

Vaping Master
ECF Veteran
Verified Member
Jun 27, 2009
9,066
19,246
UK
I got mail:
Various capacity syringes, most with a bottle adapter, a few with a tube that will reach the bottom of a bottle.

The Sigelei Mini Red -
It comes with a silicon cover on it - mine is a semi translucent white, and the USB cable is packed inside the battery compartment. 90 days warranty.
Colour is a subtle ruby type red rather than scarlet, finish is what I'd term 'frosted' rather than brushed or chromed. Not as much smooth sheen as with a blue iStick for instance. Quite nice, and not at all 'blingy'. Chrome buttons, top and base add a smart touch.
With the magnetic door being on the side, the edges are more sharply defined than on the opposite side which is neatly rounded at the edges - it makes it feel unusually sharp in the hand, but not uncomfortably so - something I'll get used to. Door is firm but easily removed using a tiny lip at the bottom of it.
Tidy inside the battery compartment. Battery a neat fit.

5 clicks for on.
A little heavier than the iStick 30W. Slightly taller but narrower than the iStick 50W. Depth approx. the same.
It was already half charged and set at 5W. I tried the Subtank nano on it at the 5W and it worked perfectly.
Now trying it with the Air-M at 7.5W, and again, it works perfectly.
Up/down buttons need a press for each step up or down unless held down for a couple of seconds delay and then it moves until released.
Fire button is smooth to touch, and responsive - has a little sideways/up-down play if pushed on lightly, but not much.
The display shows accurate ohms reading for coils used.
Only thing I'm not so keen on is that the display goes off immediately the button is released - I'd prefer a couple of seconds.

Just charging it up to full - display comes on showing the charging 'flash' on the battery icon and then it goes off ...remains to be seen what it does when charged.
 

Pictor

Vaping Master
ECF Veteran
Verified Member
Jun 27, 2009
9,066
19,246
UK
Sounds a good buy for you Trish.
My sigs display stays on but it's a different chipset i beleive.
So far, it seems rather nice!
At one point, I did press the 'up' button, and alongside the displayed wattage, it showed 'M2' and bounced the wattage up to 15W ...not one for reading instructions (particularly ones translated from Chinese) so haven't tried to find out what it means ..probably nothing I need to know ;)
 

Brynglas

Vaping Master
ECF Veteran
Verified Member
Sep 22, 2014
4,561
6,449
ΩFlint MountainΩ
So far, it seems rather nice!
At one point, I did press the 'up' button, and alongside the displayed wattage, it showed 'M2' and bounced the wattage up to 15W ...not one for reading instructions (particularly ones translated from Chinese) so haven't tried to find out what it means ..probably nothing I need to know ;)

It has presets on it Trish.
You can set your favorite 5 wattages and just change with one push of the button.
Saves scrolling up and down.Very handy.
 
  • Like
Reactions: Pictor

Pictor

Vaping Master
ECF Veteran
Verified Member
Jun 27, 2009
9,066
19,246
UK
It has presets on it Trish.
You can set your favorite 5 wattages and just change with one push of the button.
Saves scrolling up and down.Very handy.
Ah! I see - thanks.
Perhaps need to read those instructions at some point, but I vary the wattage by fairly small amounts, so it probably won't be something I'd use much anyway :)
 
  • Like
Reactions: Brynglas

Bobw1951

Vaping Master
ECF Veteran
Verified Member
Feb 23, 2014
6,890
9,913
London, UK
If you think of the design of the subtank Bob,don't think they could have made them any other way.Top section of the chimney needs to be part of the top cap.

and because it is made of Acrylic the tube part may be liable to crack if the OCC/Rebuildable deck gets too hot - as I said, I'll pass and stick with the glass tanks for the subbys, if any of them need to leave the house I have 3 protector rings that can be put round them.
 
Status
Not open for further replies.

Users who are viewing this thread