• This forum has been archived

    If you'd like to post a thread, post it here instead!

    View Forum

Fasttech Veterans

Status
Not open for further replies.

Bobw1951

Vaping Master
ECF Veteran
Verified Member
Feb 23, 2014
6,890
9,913
London, UK
Must say i enjoyed my time down there, and Boscombe is fine.Only got out to Poole the once and no further,so i missed the dregs.:laugh:
A girl i went to primary school with and lived next door to in Boscombe is still down there.


Another Flask for sale on UKV this morning :confused:

Just seen that one, don't think it was a DNA40 though v2.1 came in DNA30 as well as DNA40, think he would have mentioned it being DNA40 if it was, and being bought in September makes me doubt it as well.
 

Pictor

Vaping Master
ECF Veteran
Verified Member
Jun 27, 2009
9,066
19,246
UK
Trisha, Just loaded a MOW up with Kingslayer, the same as you have 3mg max VG, and the maximum wattage I can get it to is 16.8w on the istick and it is quite good.

EDIT: Had to take it down to 13w as it wasn't feeding the juice very well at 16.8w
Suppose that's not too bad for a fairly simple tank?
Would it have performed better at higher watts with a higher PG ratio?

I must say, apart from the basic Evod, these are the most consistent I've used - and any others that have a larger capacity like the mega MOW has, have all gurgled, leaked and been an absolute pain. My two mega MOW's have had tiny air hole leaks at odd times, but nothing much, and the standard size has never given me any problem at all. I have 5 standard size in use and one or two mega's (one has the Donut King). Plus two mini Nautilus that always have Mint Choc Vapetto and Posset in them :)
 

Brynglas

Vaping Master
ECF Veteran
Verified Member
Sep 22, 2014
4,561
6,449
ΩFlint MountainΩ
That's the place Terry.
My problem was it wouldn't let me change the address from Ireland to the UK.
Bob contacted them and they said,make sure your Postcode is there and correct and they'd push it through.
Don't know about the problem you have encountered.But i'd try without changing the country away from Ireland.
 

Brynglas

Vaping Master
ECF Veteran
Verified Member
Sep 22, 2014
4,561
6,449
ΩFlint MountainΩ
Just seen that one, don't think it was a DNA40 though v2.1 came in DNA30 as well as DNA40, think he would have mentioned it being DNA40 if it was, and being bought in September makes me doubt it as well.


Must be a 40 Bob,he's including a roll of ni wire.
 

Bobw1951

Vaping Master
ECF Veteran
Verified Member
Feb 23, 2014
6,890
9,913
London, UK
Suppose that's not too bad for a fairly simple tank?
Would it have performed better at higher watts with a higher PG ratio?

I must say, apart from the basic Evod, these are the most consistent I've used - and any others that have a larger capacity like the mega MOW has, have all gurgled, leaked and been an absolute pain. My two mega MOW's have had tiny air hole leaks at odd times, but nothing much, and the standard size has never given me any problem at all. I have 5 standard size in use and one or two mega's (one has the Donut King). Plus two mini Nautilus that always have Mint Choc Vapetto and Posset in them :)

It's possible but still no higher than 16.8 with that head in the MOW - forgot to mention it was 1.8 ohm, of course a lower resistance would allow it to go higher. I've always got those flavours on the go in one tank or another, mainly in the Lemos or Kayfuns.
 

Bobw1951

Vaping Master
ECF Veteran
Verified Member
Feb 23, 2014
6,890
9,913
London, UK
@ George/Bob

The place in ireland where you got your Quack juice ! Is it called cigatec ? I have just registered with them, and tried to buy some Goose, but it is telling me there is no carrier available. How did you get round it ? something to do with putting ireland in your Address ??

Use the normal checkout not the quick Paypal one and then as George has said.
 

Pictor

Vaping Master
ECF Veteran
Verified Member
Jun 27, 2009
9,066
19,246
UK
It's possible but still no higher than 16.8 with that head in the MOW - forgot to mention it was 1.8 ohm, of course a lower resistance would allow it to go higher. I've always got those flavours on the go in one tank or another, mainly in the Lemos or Kayfuns.
I mostly have 1.8 and 2.0, and FT have some 2.1 I believe. But, as you'll know, they go down to 0.8ohm.
So, all considered, they aren't bad tanks :) (I have a fair few unused 'spares' too ;))

Funny how much different the Cloupor Mini is after I've been so used to the iSticks - the Mint Choc Vapetto seems to have found a home with it ...at 8W! :laugh:
The LCCC seems to prefer an iPow at 6.5W, and everything else likes the iSticks :)

If you like a bit more 'oomph' in any of the lemon ones, I can definitely recommend a couple of drops of the FA Lemon Sicily flavouring in a tank! ...proves not all flavours are made the same too because I get no problems with it!
 

terry w

Vaping Master
ECF Veteran
Verified Member
Sep 1, 2012
8,666
10,916
Manchester UK
That's the place Terry.
My problem was it wouldn't let me change the address from Ireland to the UK.
Bob contacted them and they said,make sure your Postcode is there and correct and they'd push it through.
Don't know about the problem you have encountered.But i'd try without changing the country away from Ireland.

Use the normal checkout not the quick Paypal one and then as George has said.

Ok chaps, as you will see there is nowhere to even add my post code :laugh:View attachment 406421
 

terry w

Vaping Master
ECF Veteran
Verified Member
Sep 1, 2012
8,666
10,916
Manchester UK
Just put it in and explain why....additional information box.
I know they are Irish but i'm sure they'll manage :laugh:

What's the worse that can happen,they'd just refund your Paypal:)

Cheers george, i can`t pay using paypal because They won`t ship to the address what is registered there.

EDIT: Ignore that George, i just placed an order and it accepted pp :) I just put my postcode in the last line of my Address, and left them a note saying it was in england. :laugh:
 
Last edited:
Status
Not open for further replies.

Users who are viewing this thread