First day RM2 issues.

[Primulas]

Just got my RM2 a day or so again and i'm having some issues getting it up and running. I've tried 2 separate coils and neither will fire at all. Here's a pic of the better of the two.



Any ideas what could be causing this to not fire?

Also i had some issues with the posts wanting to screw out when loosening the leg screws. Could the posts not being tight enough be causing them to not create the circuit?

Thanks

 

[Big Hitter]

Not sure, do you have another mod you could try it on ??

That would eliminate connection issues on the REO

I assume the REO is firing other attys correctly ?

 

[bushmaster]

Do you have a multimeter to check from post-to-post if you have a proper connection and what your ohms might be?

 

[Evil Speakers]

Are you using any o rings? While attempting to line up the coil where I wanted it I tried to use a bigger o ring than the one that came with my RM2 in my mini and it wouldn't fire.

 

[JC Okie]

Primulas, you're using it on a Mini, right? We need to make sure it's actually making contact with the 510 connection in the mod. I'm wondering if maybe you didn't get one that was milled down (even though you said you asked Rob to mill it down to fit a Mini...right?) Do you by chance have a 510 adapter? Or....put it on another mod just to see if it's actually firing anywhere. The legs of the RM2 should not be loose so make sure they're screwed in tightly.

I know I've tried an RM2 or two on my Minis and they seem like they fit, but they're not screwing down tightly enough to make connection. The milled down ones work fine. That's all I can think of.....

 

[Dturp]

Primulas, you're using it on a Mini, right? We need to make sure it's actually making contact with the 510 connection in the mod. I'm wondering if maybe you didn't get one that was milled down (even though you said you asked Rob to mill it down to fit a Mini...right?) Do you by chance have a 510 adapter? Or....put it on another mod just to see if it's actually firing anywhere. The legs of the RM2 should not be loose so make sure they're screwed in tightly.

I know I've tried an RM2 or two on my Minis and they seem like they fit, but they're not screwing down tightly enough to make connection. The milled down ones work fine. That's all I can think of.....

That's what I'm thinking. The mini I have with the RM2 I have it screws on but not enough to make full contact.

 

[Primulas]

I'll try to find my multimeter and try it on my k100

 

[Primulas]

Yes hits great on my k100. Must not be making contact.

 

[Dturp]

If you're sticking the o-ring that came with it under it try it without it. Otherwise might need to go back to rob

 

[nerak]

If it is screwing down to almost make contact you can try to turn the center post and bring it out a little. Sometimes that will be enough to make contact. Be careful though, you don't want it loose, it could cause a short.

 

[redeyedancer]

When she says adjust the screw she means the screw on the atomizer .Adjusting the screw on the mod will cause problems . You can try turning it counter clockwise 1/4 turn . Don't unscrew it anymore then 1/4 .
Your gasket in your mod may be over compressed

 

[Primulas]

When she says adjust the screw she means the screw on the atomizer .Adjusting the screw on the mod will cause problems . You can try turning it counter clockwise 1/4 turn . Don't unscrew it anymore then 1/4 .
Your gasket in your mod may be over compressed

Adjusted center pin one quarter turn to the left. Still no contact.

 

[redeyedancer]

Adjusted center pin one quarter turn to the left. Still no contact.

Toss the mini in a padded envelope send it to me .
Please put
a note with your email address and a brief description of the problem .Also
empty any e juice in the mod and remove the bottle .It helps to put a tissue
or napkin around the tube .

Reos Mods LLC
120 Ida Jim Rd
Alfred Me 04002

 

[debzcf]

Toss the mini in a padded envelope send it to me .

You're such a good doobie.

 

[bsidb]

nice service

 

[bushmaster]

You're such a good doobie.

I think they hate it when you say "doobie" on ECF.

 

[Primulas]

Toss the mini in a padded envelope send it to me .
Please put
a note with your email address and a brief description of the problem .Also
empty any e juice in the mod and remove the bottle .It helps to put a tissue
or napkin around the tube .

Reos Mods LLC
120 Ida Jim Rd
Alfred Me 04002

Thanks Rob. Will do; tho might be a bit as my mini is my only vape as my gf has claimed my k100. I'll see if I can borrow a buddies extra mod on Monday.

Thanks everyone.

-primulas

 

[MamaTried]

I think they hate it when you say "doobie" on ECF.

LOL. i might actually spend more on paper towels this month than on Reos

 

[pdib]

You're such a good doobie.

Romper Room?


really?



huh.








heh.

 

[debzcf]

Romper Room?

Yeah...what of it? I was not a deprived youngster -- that and "Captain Kangaroo" brought me joy.

and Soupy Sales (but he was a bad boy).