Fogger V4!!

[pmcode]

I must have missed that one, I was looking for the fogger name inside on the chamber section, and I was looking at it on my phone sorry for the confusion.

Nothing but a thing.

I finally ran out of AiV juice had to rewick to use some local B&M stuff I picked up as crisis juice. I must say, definitely beware when changing juice consistency. Used the same wicking technique (wick about half-way down channel), and this thing flooded like Nawlins after Katrina (sorry, too soon?) All down my brand new V3 Flip, thought the wife was gonna have a heart attack, or at least make me have one. Thin juice most surely needs A LOT more wick....

 

[dwcraig1]

I am at work now so what I can do with my Fogger v4 is limited but here it is what I just did:
Just something I was thinking about so I thought I'd give a try.
On re-assembly I screwed the chamber with it's stem tightly into the top cap, I then screwed on the assembled base similar to how an Aqua is filled upside down. This allows for the chamber to not be all the way down on the deck threads, again similar to Agua with liquid control partially open.
So far so good

 

[Muggs]

Just bought the v4. I think this thing is going to be my end all be all. I love my v2 and the v4 touches fixes any little gripes I had with the v2. Can't wait to build this thing.

 

[suspectK]

I should have mine Wednesday/birthday. W007!

37, ph0n3 h0m3.

 

[csantiago1911]

Mine made it from China to the US (San Francisco) as of Saturday... hopefully I will receive it soon. The waiting sucks!

 

[dwcraig1]

On the Fogger v4 be expecting the o-ring on the fill screw to tend to stay in the base when removing said screw and retrieve it before you lose it.
I have replaced mine with one of the small red o-rings that come with most Aqua's, at least now I can see it. I haven't lost the original yet but have had several almosts.

 

[VaPreis]

Received my Fogger V4 today from Fasttech. Record timing....9 days from order to my door step.

Seemed to have nailed it on the 2nd build. 1/16"ID microcoils, 28ga wire, 9 wraps each for a total of 0.6Ω. Wicked it with CVS organic cotton balls. This thing is a cloud machine and overall, I'm thrilled with it. First build was similar, but I tried Peaches and Cream yarn for wick. It fits nicely, but gave dry hits after a few pulls, and if I can't chain vape it, then it's crap.

Overall, the quality seems pretty nice and it looks great on my V3 Flip. My only problem with it is that the base section just above the air flow control on mine does not come off. In the videos I've seen, it does. I tried twisting it till I was red in the face, and it didn't budge. Not a deal breaker, you can build it and wick it with this section on.

 

[pmcode]

Received my Fogger V4 today from Fasttech. Record timing....9 days from order to my door step.

Seemed to have nailed it on the 2nd build. 1/16"ID microcoils, 28ga wire, 9 wraps each for a total of 0.6Ω. Wicked it with CVS organic cotton balls. This thing is a cloud machine and overall, I'm thrilled with it. First build was similar, but I tried Peaches and Cream yarn for wick. It fits nicely, but gave dry hits after a few pulls, and if I can't chain vape it, then it's crap.

Overall, the quality seems pretty nice and it looks great on my V3 Flip. My only problem with it is that the base section just above the air flow control on mine does not come off. In the videos I've seen, it does. I tried twisting it till I was red in the face, and it didn't budge. Not a deal breaker, you can build it and wick it with this section on.

Further proof that great minds think alike.......

 

[roflwaffles]

Someone with a Panzer post a pic with this on it please

 

[suspectK]

Just got a message from eBay seller that they are getting an updated fogger v4 in tomorrow with better airflow. They haven't sent mine yet, so I was asked if I prefer to wait to get the revised version. ...but also ×2.

Froginfog is sellers ID.
I had some newb error with this one... just noticed seller has 0 feedback... and it's shipping from Hong Kong..pay pal will keep me safe I guess. It would've been nice to get that message last week.

37, ph0n3 h0m3.

 

[Muggs]

Love the pics and input. I'm looking forward to a dual coil build. The singles have been fun but like my drippers that .7ohm or .6ohm dual setup is just another level.

BTW you guys know that white rubber ring we have to have over our wicks before screwing the chimney down? I just use a different O ring from one of my dripper kits which is a tad thicker and easier to slip over the cup, works great.

My fill screw is stripped on my v2. I pull the top cap off, push the screw out of the top cap, fill up and have to put the top cap on before putting the fill screw back in because it would be too much pressure with it in place while pushing the top cap back on the glass tank. Looking forward to be able to just unscrew the screw and fill.

 

[VaPreis]

Just got a message from eBay seller that they are getting an updated fogger v4 in tomorrow with better airflow. They haven't sent mine yet, so I was asked if I prefer to wait to get the revised version. ...but also ×2.

Froginfog is sellers ID.
I had some newb error with this one... just noticed seller has 0 feedback... and it's shipping from Hong Kong..pay pal will keep me safe I guess. It would've been nice to get that message last week.

37, ph0n3 h0m3.

No offense, but that sounds like a line. The airflow on this thing is pretty wide open. You can easily lung hit it. Even with .6Ω build in it, I partially close off the air flow for my tastes.

I did notice that Fasttech posted the black version this morning.....right along with the black copper Stingrays.

 

[VaPreis]

Someone with a Panzer post a pic with this on it please

On the Panzer (clone)

 

[suspectK]

No offense, but that sounds like a line. The airflow on this thing is pretty wide open. You can easily lung hit it. Even with .6Ω build in it, I partially close off the air flow for my tastes.

I did notice that Fasttech posted the black version this morning.....right along with the black copper Stingrays.

None taken... I had literally just woke up when received email..and literally just got up when I posted about it. Maybe the revised version has a fix for the loose ring? When I purchased it, the black was available as an option...so maybe this was the intention the whole time to list something without having it...who knows. All I know...I'm ...... about not having one for my birthday.

 

[Blktmnt]

I thought about getting the fogger with the black finish. I am just afraid that the black finish will start to chip off. I makes me just want to go the stainless steel route and not have to worry but i like the black to chrome to black look it would give me on my mod. AHHHHHHHHHH

 

[Muggs]

Yeah go with the stainless my friend. Like you said that black finish will eventually come off. But man it would look so good on a black mech.

 

[suspectK]

^Or a mod like a hana...

 

[Gonzi]

I'm contemplating getting a black one for my black Stingray. I already have a black KFL clone on pre-order for it, waiting for it to hit my mailbox. This Fogger V4 looks nice, might just have to order it and hope that the wife doesn't mind too much.

 

[dwcraig1]

I'm contemplating getting a black one for my black Stingray. I already have a black KFL clone on pre-order for it, waiting for it to hit my mailbox. This Fogger V4 looks nice, might just have to order it and hope that the wife doesn't mind too much.

I'm interested in the copper screw, I can always buff it when the black comes off.

 

[Gonzi]

I just ordered the black version from Fasttech! The more toys the better!