Fogger V4!!

[G-weezy]

Tried to find more info on modding the Fogger. But didn't find much. So I went ahead and gave it a shot. Drilled out the 2 air holes and the air channel to the coils at 3mm. Also chamfered them. Will do a build when I get home and see how it works. Also cleaned out the positive pin with some Brasso.

 

[Tbev]

I cant wait to hear how well that goes? 3mm is big!

 

[G-weezy]

You know what sucks? I wanted to try this so bad but my screws are stripped I'm looking for my extra screws but nothing is fitting. Might have to drill holes in the post and go atty style.

 

[TheKiwi]

You know what sucks? I wanted to try this so bad but my screws are stripped I'm looking for my extra screws but nothing is fitting. Might have to drill holes in the post and go atty style.

Grin.

AMD will come in shortly to offer his expertise on tapping the posts to a new size.

 

[AMDTrucking]

Grin.

AMD will come in shortly to offer his expertise on tapping the posts to a new size.

Ha Ha Ha

But if you ship it to me I will gladly re-thread your posts to M2-0.40 and even include new screws absolutely free of charge.

 

[AMDTrucking]

You know what sucks? I wanted to try this so bad but my screws are stripped I'm looking for my extra screws but nothing is fitting. Might have to drill holes in the post and go atty style.

I think I replied to a wrong poster.

if you ship it to me I will gladly re-thread your posts to M2-0.40 and even include new screws absolutely free of charge.

 

[G-weezy]

I think I replied to a wrong poster.

if you ship it to me I will gladly re-thread your posts to M2-0.40 and even include new screws absolutely free of charge.

Nice. I appreciate the offer. I'll PM you when I decide what to do. Just sucks that it happened when I was ready to build.

 

[BNEAT]

OK fellas, it's official: The Eleaf Lemo is my new favorite tank!

My dual coil build was (mistakenly) 26 gauge, and they were taking way to long to heat up at my usual power settings. I just thought the Lemo didn't produce as much vapor. So I built it with a couple of 28 ga coils, 2.2dia x 8 (.7ish ohms) and now this tank rolls coal! Every bit as much vapor as my Foggers, and I think it taste just as good, if not better! Typical KF build, Rayon with thinned tails on the deck.

I wish another one of you Fogger fanboys had an eVic Supreme so you might want to try one of these things. (of course, it would look just fine on a box mod)

 

[TheKiwi]

What's the largest airhole size?

 

[BNEAT]

I'm not sure what size the main air hole is on the deck, probably close to 4mm? (it looks huge) The 4 small air holes are 1.8mm. With the AFC all the way open it's pretty airy. Not cloud-chasing airy, but pretty decent air flow.

 

[BNEAT]

AMDtrucking, I know how much you love these things: MadVapes has the Big Buddha for $39.89 with the coupon code "ECF5OFF"

EHPro Big Buddha V1

 

[AMDTrucking]

AMDtrucking, I know how much you love these things: MadVapes has the Big Buddha for $39.89 with the coupon code "ECF5OFF"

EHPro Big Buddha V1

Thanks, but I already have one.

 

[TheKiwi]

I'm not sure what size the main air hole is on the deck, probably close to 4mm? (it looks huge) The 4 small air holes are 1.8mm. With the AFC all the way open it's pretty airy. Not cloud-chasing airy, but pretty decent air flow.

Ah. Compared to a fogger?

I find the stock fogger air holes are a little tight even when fully opened.

At this point I wouldn't buy any kayfun-ish atty (I have 4 authentics and 5 clones), unless I can get significantly better airflow, or perhaps a more native dual coil capability (kinda like a big Buddha, but in 22mm)

 

[AMDTrucking]

Anybody tried this one yet?

Besides the threaded polycarbonate tank, of course

 

[Tbev]

I've heard a few people who like em, but again, that tank..

 

[AMDTrucking]

I've heard a few people who like em, but again, that tank..

I know, ha... The tank...

I went ahead and ordered it for $27.00

I like that Stainless Steel Stand that comes with it. I figured, it'll cost me more then $27.00 just to make one.

 

[Tbev]

Right, lol, have you seen my stand?


http://www.e-cigarette-forum.com/forum/showthread.php?t=507900
My Atty Rack, Solid Billit Aluminum

There's pics of a couple different ones.

 

[AMDTrucking]

Right, lol, have you seen my stand?


My Atty Rack, Solid Billit Aluminum
My Atty Rack, Solid Billit Aluminum

There's pics of a couple different ones.

Looks cool.

 

[TheKiwi]

Anybody tried this one yet?

Besides the threaded polycarbonate tank, of course

LINK PLS! I've been looking for one!

 

[b.m.]

There are a few people selling the clones on ebay in the $40-$45 range,and 1 listing for an authentic at $200.