The fogger will only fit on a VTR if you cut off the VTR ring and also leave off the airflow ring. It's a tight 22mm
Fogger V4!!
- Thread starter Shofixti
- Start date
- th_trl_thread_readers 0
- Status
But even for 21mm tank, you'll still have to widen your VTR ring.
IMHO: Dual coil RTA's (Ithaka, Aqua, Fogger, Orchid, Billow) are NOT the best choice for Innokin iTaste VTR because, unless you want to deal with ridiculous flimsy 32 gauge coils, it is hard to get decent performance at 15 Watts.
I routinely work with those "flimsy" 32 gauge coils and use 33 and 34 gauge as well, depending of the particular re-build requirements. The build on my VTR, at the moment, is a net 1.9 ohms of 32 gauge, NR-R-NR. I am going to rebuild it though, it has about 60ml through it and it's starting to show signs of lower performance.
Wicking can be more of a challenge, but finesse develops with time and patience. I will admit to walking away a few times to keep fro getting overly frustrated though.
I guess I'll be picking up a brake hone to take some of the ring off. 21mm isn't too bad and will leave enough material to be at lest somewhat functional.
Wicking can be more of a challenge, but finesse develops with time and patience. I will admit to walking away a few times to keep fro getting overly frustrated though.
I guess I'll be picking up a brake hone to take some of the ring off. 21mm isn't too bad and will leave enough material to be at lest somewhat functional.
somewhat functional?
It is fully functional and strong enough to support the tank.
And the Erlkonigin, you won't have to remove the tank from the Mod to re-fill it:
Although, it is always a good idea to shut the airflow down when re-filling from the top. IMHO
Last edited:
I like that an 18 gauge needle fits the refill hole, too. I'm not at my desk, so I can't see my notes on the VTR ring diameter and thickness, but from the photo it looks pretty substantial after modification. Thanks for the air flow tip, I'm usually messy anyway.
Even better! An 18 would be better than the 20 the Fogger seems to be limited to because of the location of the fill hole in the tank versus the deck. I can get a 19 gauge in, but it's not a big enough improvement.
I don't know about you people, but I needed a grip tool to unscrew a part of my atomizer that is stuck and doesn't want to be unscrewed by hand.
Something that will get a good grip on it without damaging the finish.
I couldn't find one. So I took a Vise-Grip and 22mm grinding stone and made me one. Yes, I put a layer of paper there to prevent any scratches.
Something that will get a good grip on it without damaging the finish.
I couldn't find one. So I took a Vise-Grip and 22mm grinding stone and made me one. Yes, I put a layer of paper there to prevent any scratches.
That's actually a really cool idea.You can pick up a cheap set of those pliers,and make that very cheap.I would even go a step further though,and grind those extra teeth off so it is all smooth.
I use ChannelLocks for pipe, curved jaws, and those nice grippy rubber pads you use in the kitchen for opening jars, but your solution is a lot more elegant, AMD.
Last edited:
Take a look at this: EVKOO Vapor Flask V2 40W Clone $65.00 Shipped
I know nothing about this one (other then I have placed an order for one 20 - 30 days shipping from China)
I'm sure it doesn't have an authentic Evolv DNA40 in it, but for $65.00, even if I will have to purchase DNA40 ($60.00) - I'll end up with Vapor Flask for $125.00
These pictures are linked to their Website:
I know nothing about this one (other then I have placed an order for one 20 - 30 days shipping from China)
I'm sure it doesn't have an authentic Evolv DNA40 in it, but for $65.00, even if I will have to purchase DNA40 ($60.00) - I'll end up with Vapor Flask for $125.00
These pictures are linked to their Website:
Last edited:
Looks awesome but maybe it's just photos of the original or a special made prototype?
Looks just too good to be true haha.
Looks just too good to be true haha.
I'll let you know when it gets here in 20 - 30 days...
I don't expect much from it, I'm basically buying an enclosure.
Last edited:
E.H.Pro Billow evolution:
I started with 28 Gauge spaced coil at 0.704Ω it sucked.
Then I did 26 Gauge micro coil at 0.411Ω better, but not best.
And the last one: 0.9mm flat ribbon at 0.278 Ω I think I like my Billow now.
I can't wait to see how this turns outTake a look at this: EVKOO Vapor Flask V2 40W Clone $65.00 Shipped
I know nothing about this one (other then I have placed an order for one 20 - 30 days shipping from China)
I'm sure it doesn't have an authentic Evolv DNA40 in it, but for $65.00, even if I will have to purchase DNA40 ($60.00) - I'll end up with Vapor Flask for $125.00
These pictures are linked to their Website:
Mini Fogger mod time: Without modifications this tank was unvapable for me...I like them airy!
More air!
Less metal = more air
Not exactly a direct path to the coil, but the chamber is so tiny it doesn't seem to matter
More air means more juice
This little tank is the best tasting vape I've ever had, including my drippers! Coil is 28awg x 2.2mm @ 1.4ohms, vaping at 20watts regulated, and of course, wicked with Rayon
More air!
Less metal = more air
Not exactly a direct path to the coil, but the chamber is so tiny it doesn't seem to matter
More air means more juice
This little tank is the best tasting vape I've ever had, including my drippers! Coil is 28awg x 2.2mm @ 1.4ohms, vaping at 20watts regulated, and of course, wicked with Rayon
Last edited:
Best tasting vape ever! I'm convinced it's the itty-bitty little chamber in this thing: The Vape is super rich tasting. It's only a single coil, so the vape production isn't nearly as thick as my other tanks. But what it lacks in vapor, it more than makes up for in flavor.
- Status
Similar threads
- Locked
