Geekvape Griffin RTA!

[Quantum Mech]

I run about 65 that's 4 below what grimm runs his at and its about the same build

Try dropping the watts

This only needs 50

 

[KayP]

Try dropping the watts

This only needs 50

View attachment 533119

I recognise that deck and base [emoji1]

Sent from my SM-G900I using Tapatalk

 

[Haylon357]

mine does that also if i dont have all 3 pieces tight... just mess around with it and keep spinning the tank (clockwise like 10 times, with the tank on) and see if you can figure it out. im still unsure on how it fully works. JFC is weird too

I have spent most of the morning trying to figure out how to disassemble the deck. I'm sure I could fix the easy spinning afc and jfc. But I'm totally at a loss.

Sent from my VS986 using Tapatalk

 

[RAWRferal]

I've attached some pictures of my build, can you guys see any reason for it to be giving dry hits? Thanks

Your build looks fine, make sure your juice control is FULLY open, best tip ever with this tank. Spin it a little further after you see it open, you want the holes on the chimney aligned with the middle of those deceptively wide slots.

 

[EthanThorn]

Try dropping the watts

This only needs 50

View attachment 533119

Still wicks really slow


Sent from my iPhone using Tapatalk

 

[EthanThorn]

Starting to think that the juice wells don't match up with the juice flow holes


Sent from my iPhone using Tapatalk

 

[xVape]

Your build looks fine, make sure your juice control is FULLY open, best tip ever with this tank. Spin it a little further after you see it open, you want the holes on the chimney aligned with the middle of those deceptively wide slots.

Thanks for the help, it turned out to just be the wicking, it was way too thick I think. I ended up just rewicking, I made the wicks a lot thinner and fluffier and now I can chain vape without any signs of a dry hit. Great tank, if you get the wicking right!

 

[EthanThorn]

Ok i think i got it not to loose but not to tight now to work on my other RTA thank you for all the help

 

[Bman123]

I'm so on the fence about getting this rta. I had a mutank before and I did like it but sold it because I got bored with it.

I've seen some cool pics of huge coils in this rta

Sent from my Nexus 6 using Tapatalk

 

[Haylon357]

I contacted Geekvape about my wife's loose afc and jfc rings. They are sending me a new one. Top notch service people. They actually back their product.

Sent from my VS990 using Tapatalk

 

[Bman123]

I contacted Geekvape about my wife's loose afc and jfc rings. They are sending me a new one. Top notch service people. They actually back their product.

Sent from my VS990 using Tapatalk

That sounds like the icing on the cake for me right there. It's hard to find a company that actually gives a ....e about the people who buy their products

Sent from my Nexus 6 using Tapatalk

 

[Haylon357]

I only had one other company do that and that was Flawless.

Sent from my VS990 using Tapatalk

 

[Uncletattoowhat]

I contacted Geekvape about my wife's loose afc and jfc rings. They are sending me a new one. Top notch service people. They actually back their product.

Sent from my VS990 using Tapatalk

Nice! I'm going to contact them about my loose jfc as well then! It's the only thing I dislike about this tank.

 

[KayP]

Loose AFC ring, what exactly is it doing. Do mean there's not enough resistance and does not stay at your preferred air flow setting? Or that it does not stop at any point allowing you turn it 360 degrees?

Sent from my SM-G900I using Tapatalk

 

[Haylon357]

Loose AFC ring, what exactly is it doing. Do mean there's not enough resistance and does not stay at your preferred air flow setting? Or that it does not stop at any point allowing you turn it 360 degrees?

Sent from my SM-G900I using Tapatalk

My wife's afc and jfc turn with no resistance what so ever. She constantly has to adjust it.

Sent from my LG V10 using Tapatalk

 

[MadTemp]

I like that Brian on TVC compared it to the crius. 3mm Clapton is pretty impressive. The one thing I am curious about is refilling. From what I've seen in these videos there is no seal inside the top cap. The only thing I see is an o ring under the thread on the body. I wonder if juice will be on the threads when opened which could be messy. Guess I will have to see some real world useage.

no problems there, wicking is better on the griffin if they just SIT on top, don't cram them in

 

[Bman123]

Has anyone here tried the Gemini tank? Looks just like the Griffin but it has to pair flow like the herakles plus

Sent from my Nexus 6 using Tapatalk

 

[KayP]

My wife's afc and jfc turn with no resistance what so ever. She constantly has to adjust it.

Sent from my LG V10 using Tapatalk

That's a shame. It's good to hear they're replacing your unit. Geekvape does need to improve their quality control though, as I had to have my first unit replaced too (broken glass and stuck grub nut). I'm very happy with my replacement, I hope you will be too [emoji1]

Sent from my SM-G900I using Tapatalk

 

[Roadtrip635]

I just saw this today, for any one wanting to add top airflow to their Griffin. Not quite like the Gemini, but it's an option for those those wanting more airflow

GeekVape Griffin Top Airflow Set - SS

 

[KayP]

Has anyone here tried the Gemini tank? Looks just like the Griffin but it has to pair flow like the herakles plus

Sent from my Nexus 6 using Tapatalk

Nope. There's a few reviews floating around and it looks to be better than the Griffin in many ways. If I wasn't happy with, or hadn't purchased the Griffin, I'd go for the Vaporesso.

Sent from my SM-G900I using Tapatalk