GeekVape Zeus RTA
- Thread starter Gallant
- Start date
- th_trl_thread_readers 0
- Status
Yes. I'm OCD as Hell and this thing drives me absolutely nuts. I've considered covering the tank with some bands just so I don't have to see it off center.
Oh damn my cheeks are starting to hurt.
I have had a headache all day so have tried to stay away from here because laughter might be good medicine but it isn't good for a headache.
It seems to be better now, so I ventured back.
You did miss a few chuckle worthy posts. Glad you are feeling better.I have had a headache all day so have tried to stay away from here because laughter might be good medicine but it isn't good for a headache.
It seems to be better now, so I ventured back.
After less than a day of vaping the provided 510 drip tip is rather loose. So much so I believe it would just pop off while in my pocket. Anyone else? Better o-rings the answer I'm guessing?
I like the looks of the other two more but with my simple build the flavor is so much better with the 510.
I like the looks of the other two more but with my simple build the flavor is so much better with the 510.
I just put a thicker o-ring on my 510.
Love this tank. It has taken the place of my 1.5 year old Kayfun v5 clone. So nice to not have condensation all over the place. I'm also thinking Zeus won't have to have constant o-ring replacement to prevent leakage. Very nice.
Seems the clone factory was sent the wrong Zeus?
$15.21 Zeus Styled RTA Rebuildable Tank Atomizer - 3ml / stainless steel + glass at FastTech - Worldwide Free Shipping
$15.21 Zeus Styled RTA Rebuildable Tank Atomizer - 3ml / stainless steel + glass at FastTech - Worldwide Free Shipping
Been running my Zeus with little trouble, however, have an observation and a question. When I fire up my mod (Tugboat dna 75), the first couple of hits are very muted and until the Zeus warms up there isn't a lot of cloud or flavor.
Is there a pre-heat function I can use...I tried to read the DNA 75 manual but I'm struggling. I vape in normal wattage mode at 31.5 watts on a 3.5mm 26/36N80 0.4 ohm coil (bought pre made).
Is there a pre-heat function I can use...I tried to read the DNA 75 manual but I'm struggling. I vape in normal wattage mode at 31.5 watts on a 3.5mm 26/36N80 0.4 ohm coil (bought pre made).
I dont know about a preheat on a DNA 75w device if you can do it it’ll probably be in Escribe. I’ll let the more experienced with DNA’s answer but,
I have fused Clapton wire 26*2/36N80 also with 3.5mm & .4 ohm coil I’m using on the single coil deck for the Aromamizer Supreme V2 & it needs 33 watts & a preheat with the Hard option on my Minikin v2. Maybe try to up the wattage a bit for now until someone can answer about a preheat on a DNA device?
I run mine using a 7 or 8 wrap, SS 316L which comes in right around .35-.42 ohms at 35-42.5. And I always get a muted hit if I just draw on it. What I have found is that the best thing to do for me is to purge it and then draw. Blow out through the Zeus for a second or so, and then draw in. Getting tons of flavor with that.
No preheat in power mode for dna. However on forum.evolvapor I've seen where some have successfully cheated and got their device to act like there is. It looks like a pain to achieve, and not everyone is successful. Use at your own risk. I do TC, so I have not tried this or read the entire thread, which it looks like most have to do in order to achieve this.
While I understand dna's focus is TC, I think they really should have worked preheat into power mode, unless of course something is preventing it on the board or something. I can preheat in power mode on my old evic vtc mini with arctic fox firmware, so I was shocked to not see this option when I first configured my dna75.
Last edited:
- Status
