- Status
Who DARED to buy this?! Speak now... I wanted this"The Ghost" is SOLD
Thanks
(Saw it @ VapeP***)...*sigh* maybe next one..
Hello
Today For SALE
Gepetto Art - "The Spider" VV - With NEW ELECTRONICS
hand made wooden box mod with 510 connection that takes 2 16340 . It is carved out of a single block of wallnut and it has a chiseled one of a kind engraving.
Variable Voltage
Specifications for electronic components
Main features:
* Operated with one button.
* 2 digit, 7 segment 5mm LED display
* Powered by 2 stacked Li-Ion batteries ,Protected batteries are recommended.
* Works with 1.0 to 5.0 ohm coils
* 3,0V to 6,0V regulated, in 0,1V increments.
* Displays current power left with load and w/o load.
* Shorted coil indicator.
*Coil pre-heating function. Might come in handy on cold days or when we`re using thicker e-liquids.
- Eight pre-defined heating characteristics (A1 to A8)
- One heating characteristic that can be modified by the user (A9) (we can program up to 8s of heating in 0.5s periods)
- Programable cutoff time (5 to 15s)
- Button block - press it 4 times and then hold for more than 1.5s to block the button. Press 4 times again to unblock the button.
- Protection from overdischarging the batteries - you can choose when you want the mod to stop working (between 2.7 and 2.95v per battery [5.4-5.9v total] )
How to use it ?
When we insert the batteries the module is ready to work. We use the single button.
* If we have not used the switch for the last 3-4s, module goes into ‘sleep’ mode. LED display is powered down to save battery life.
* Normal press – Coil is powered up as long as we press the button. LED shows battery voltage under load. Shortly after we release the button, voltage w/o load is displayed. If we compare these two numbers we can see how good our batteries are and we can work out their internal resistance.
* Two clicks – Coil is pre-heating. PH will be displayed on our LED. This will heat the coil with ~35% of preset voltage. Pre-heating will finish after 4s and the device will go back to sleep mode. We can press the button at any time during the pre-heating process to end it and start vaping using our set parameters.
* Three clicks – Voltage increase mode. Each following click will increase voltage in 0.1v increments. When we set the desired voltage, we need to wait 3-4s for the device to save our settings.
*Four clicks – Voltage decrease mode. Each following click will decrease voltage in 0.1v increments. When we set the desired voltage, we need to wait 3-4s for the device to save our settings.
* Five clicks – Mode select:
- A1 – normal setting, just as with any other device
- A2 – Voltage will rise from 0.0V to preset voltage over the next 2s.
- A3 – Voltage increases to 120% of what we`ve set the device to for 2s and later goes back to preset value.
- A4 – Voltage will change fluently from preset value to 120% of preset and back in 2s intervals as long as we keep the button pressed.
- A5
- A6
- A7
- A8
- A9 .
I will update the electronics specifications later on
carto-tank and batteries shown in the pictures are not for sale
Price: 190$ With Shipping
PayPal only
Important: I will soon be able to send after 8 April
Thanks
Today For SALE
Gepetto Art - "The Spider" VV - With NEW ELECTRONICS
hand made wooden box mod with 510 connection that takes 2 16340 . It is carved out of a single block of wallnut and it has a chiseled one of a kind engraving.
Variable Voltage
Specifications for electronic components
Main features:
* Operated with one button.
* 2 digit, 7 segment 5mm LED display
* Powered by 2 stacked Li-Ion batteries ,Protected batteries are recommended.
* Works with 1.0 to 5.0 ohm coils
* 3,0V to 6,0V regulated, in 0,1V increments.
* Displays current power left with load and w/o load.
* Shorted coil indicator.
*Coil pre-heating function. Might come in handy on cold days or when we`re using thicker e-liquids.
- Eight pre-defined heating characteristics (A1 to A8)
- One heating characteristic that can be modified by the user (A9) (we can program up to 8s of heating in 0.5s periods)
- Programable cutoff time (5 to 15s)
- Button block - press it 4 times and then hold for more than 1.5s to block the button. Press 4 times again to unblock the button.
- Protection from overdischarging the batteries - you can choose when you want the mod to stop working (between 2.7 and 2.95v per battery [5.4-5.9v total] )
How to use it ?
When we insert the batteries the module is ready to work. We use the single button.
* If we have not used the switch for the last 3-4s, module goes into ‘sleep’ mode. LED display is powered down to save battery life.
* Normal press – Coil is powered up as long as we press the button. LED shows battery voltage under load. Shortly after we release the button, voltage w/o load is displayed. If we compare these two numbers we can see how good our batteries are and we can work out their internal resistance.
* Two clicks – Coil is pre-heating. PH will be displayed on our LED. This will heat the coil with ~35% of preset voltage. Pre-heating will finish after 4s and the device will go back to sleep mode. We can press the button at any time during the pre-heating process to end it and start vaping using our set parameters.
* Three clicks – Voltage increase mode. Each following click will increase voltage in 0.1v increments. When we set the desired voltage, we need to wait 3-4s for the device to save our settings.
*Four clicks – Voltage decrease mode. Each following click will decrease voltage in 0.1v increments. When we set the desired voltage, we need to wait 3-4s for the device to save our settings.
* Five clicks – Mode select:
- A1 – normal setting, just as with any other device
- A2 – Voltage will rise from 0.0V to preset voltage over the next 2s.
- A3 – Voltage increases to 120% of what we`ve set the device to for 2s and later goes back to preset value.
- A4 – Voltage will change fluently from preset value to 120% of preset and back in 2s intervals as long as we keep the button pressed.
- A5
- A6
- A7
- A8
- A9 .
I will update the electronics specifications later on
carto-tank and batteries shown in the pictures are not for sale
Price: 190$ With Shipping
PayPal only
Important: I will soon be able to send after 8 April
Thanks
Hello
Today For SALE
Gepetto Art - "The Spider" VV - With NEW ELECTRONICS
hand made wooden box mod with 510 connection that takes 2 16340 . It is carved out of a single block of wallnut and it has a chiseled one of a kind engraving.
Variable Voltage
Specifications for electronic components
Main features:
* Operated with one button.
* 2 digit, 7 segment 5mm LED display
* Powered by 2 stacked Li-Ion batteries ,Protected batteries are recommended.
* Works with 1.0 to 5.0 ohm coils
* 3,0V to 6,0V regulated, in 0,1V increments.
* Displays current power left with load and w/o load.
* Shorted coil indicator.
*Coil pre-heating function. Might come in handy on cold days or when we`re using thicker e-liquids.
- Eight pre-defined heating characteristics (A1 to A8)
- One heating characteristic that can be modified by the user (A9) (we can program up to 8s of heating in 0.5s periods)
- Programable cutoff time (5 to 15s)
- Button block - press it 4 times and then hold for more than 1.5s to block the button. Press 4 times again to unblock the button.
- Protection from overdischarging the batteries - you can choose when you want the mod to stop working (between 2.7 and 2.95v per battery [5.4-5.9v total] )
How to use it ?
When we insert the batteries the module is ready to work. We use the single button.
* If we have not used the switch for the last 3-4s, module goes into ‘sleep’ mode. LED display is powered down to save battery life.
* Normal press – Coil is powered up as long as we press the button. LED shows battery voltage under load. Shortly after we release the button, voltage w/o load is displayed. If we compare these two numbers we can see how good our batteries are and we can work out their internal resistance.
* Two clicks – Coil is pre-heating. PH will be displayed on our LED. This will heat the coil with ~35% of preset voltage. Pre-heating will finish after 4s and the device will go back to sleep mode. We can press the button at any time during the pre-heating process to end it and start vaping using our set parameters.
* Three clicks – Voltage increase mode. Each following click will increase voltage in 0.1v increments. When we set the desired voltage, we need to wait 3-4s for the device to save our settings.
*Four clicks – Voltage decrease mode. Each following click will decrease voltage in 0.1v increments. When we set the desired voltage, we need to wait 3-4s for the device to save our settings.
* Five clicks – Mode select:
- A1 – normal setting, just as with any other device
- A2 – Voltage will rise from 0.0V to preset voltage over the next 2s.
- A3 – Voltage increases to 120% of what we`ve set the device to for 2s and later goes back to preset value.
- A4 – Voltage will change fluently from preset value to 120% of preset and back in 2s intervals as long as we keep the button pressed.
- A5
- A6
- A7
- A8
- A9 .
I will update the electronics specifications later on
carto-tank and batteries shown in the pictures are not for sale
Price: 190$ With Shipping
PayPal only
Important: I will soon be able to send after 8 April
Thanks
Again...you have left me in awe
It was the hundredth box
someone has a happy day today because it will get something like that
Everyone's lucky and should be extremely happy to get a gepetto....had I the funds, I would order everyone you create...mmwwaaaaa
thanks,
cool that you like my work
Unfortunately this week there will be nothing for sale, in Poland we have holidays, and I'm away, away from my workshop
but you write in this topic, you know, the topic is not dead
, maybe someone will insert pictures of his GP, or review,
In any case, I send greetings to all
cool that you like my work
Unfortunately this week there will be nothing for sale, in Poland we have holidays, and I'm away, away from my workshop
but you write in this topic, you know, the topic is not dead
, maybe someone will insert pictures of his GP, or review,
In any case, I send greetings to all
The first gepetto vv bottom feeder will be mine, I'm saying it from weeks 
I hope that it will be on a single battery and small liquid bottle (3ml) to keep the size acceptable
it would be nice to see actual photos and reviews of Gepetto models in your hands
I hope that it will be on a single battery and small liquid bottle (3ml) to keep the size acceptable it would be nice to see actual photos and reviews of Gepetto models in your hands
I hope that you have a wonderful holiday. Hope to see some reviews here myself 
I have this one. I have never done a review, so I won't try that, but I can say that it is vv and it works flawlessly. The artwork is outstanding. This has become my favorite pv.
I really want to get one of these beautiful mods. I'm just nervous about the wood getting damaged with my lifestyle. I work on cars at my job and it's usually in my pocket. Maybe I'll keep it at home and vape it on the couch like my GGTS
DM the Tiger was my favorite so far. Just such a beautiful mod. Thanks for the pics.
@ silentt: That is exactly what I do, it never leaves the house!
Thank you Huffelpuff!
Thank you Huffelpuff!
I really want to get one of these beautiful mods. I'm just nervous about the wood getting damaged with my lifestyle. I work on cars at my job and it's usually in my pocket. Maybe I'll keep it at home and vape it on the couch like my GGTS
I own a Gepetto silent, and take it to work every night...HAVE to, I love vaping with it. BUT, I keep it in my office and take another "knock around" mod out on the floor, where I work. As for transport, I just wrap it up in a cloth and put it in my lunch pail.
- Status
Similar threads
- Locked
