For this experiment I used Mesh 400, the one before that didn't work used to be Mesh 300. The mesh was bought at a german shop, I only know that it is not the mesh that is sold by themeshcompany.
GG Odysseus Mesh only, No Resistance wires needed
- Thread starter Bishopheals
- Start date
- th_trl_thread_readers 0
- Status
Sorry guys been so busy with the new VaptvLive website. Stickam closed its doors so all the hosts are learning the new software. Ill see if i CAN POST SOMETHING REAL SOON. For the record none of my videos are fake.
I'm trying to make a video using Imeos initial idea for experiment using only 1 non resistance wire and I will see if it works as well in a tank setup.
Most of you already know this but some folks may be very eager to try these things. I disclosed in my video this is not meant for non experience users. These builds are very extreme and complicated advanced builds. I don't mind if a advance user try's it but please be careful.
As i helped many folks with there coil builds through skype and oovoo I don't mind helping but please be careful.
Most of you already know this but some folks may be very eager to try these things. I disclosed in my video this is not meant for non experience users. These builds are very extreme and complicated advanced builds. I don't mind if a advance user try's it but please be careful.
As i helped many folks with there coil builds through skype and oovoo I don't mind helping but please be careful.
This is a real miracle!!! My simple measurement for the same mesh (#400) yields the following result:
Resistivity = approx. 0.1 ohm/1 cm. At a voltage of 3.7 v, we'll have 137 watts of power and a current of 37 amps!!! - A deadly device...
you forget ohms is not constant in mesh when not oxidize. see my previous video when imeo and myself did a mesh resistance wire with silica wick. Moving mesh changes ohms on fly.
I tried this with poor results so far. I used a Genesis atomizer for my setup which was running at 0.2 - 0.3 Ohms. In fact it was only running for one and a half puff before the wire melted...
How the heck do you get 1 Ohm and more with this? Even if I measure Ohms from one side of my mesh to the other I get only 0,3-0,4 Ohms and these are about 8 inches...
I did it with Zattyg while Blacksmith pro producer of vapetv was looking on. You can ask him I posted the pictures which you can see on page one. It severed and sliced the mesh. he and I are looking at a different way by adding more mesh to it since my ody i had a lot of mesh. we ohmed it out at .8 ohms on zattyg but mesh couldn't take the hit since it also melted the insulator of the inner hole where mesh goes.
Fake? Fogheeetabooutit!
Sent from my Xtreamer_Mobile_AiKi using Tapatalk 2
First off I like to say I would not JEAPORDIZE anyone. As many already know I make extremely complicated coils that many users swamp me to help show them live through skype or OOVOO. I spend many hours during week taking there hand and helping them make if its my highlander coils, quad coils, zeus coils, twisted quads etc. I spend many hours a week teaching people and offering services to help them improve their vape not only in GG but in other devices as well. If you dont want to believe that ask the cast of VapeTV,
I would not create a fake video, my witness is producer of Vapetv that he saw my ody mesh coil and saw how that pumps. Mike (blacksmith pro) even asked me to do it on genesis and so did Imeo. I tried in front of mike (blacksmithpro) which failed do to size of mesh. Mesh needs to be thicker which is why it worked beautiful on ODY. Mike and I will be working on this at a later date.
My coils are extremely complicated even for the advance users to master. Which is why on vapetv I let everyone know if your not an advance user please dont try this. I spend many hours a week teaching folks how to make these coils and sometimes it takes them 4-5 days to get a good handle on them.
Im a very busy man and Im not here to play games Im always experimenting with different coils and love helping folks get a better experience with their vape gear.
Bishop,
For those that understand and are open to considering new things, no explanation is necessary. For those that do not understand or are closed to considering new things, no explanation is possible.
You do not have to defend yourself. Let your videos speak for themselves. You may be a little over the top for some people, but your passion for vaping & for giving back are self evident.
Fooggettttabbbout it!
For those that understand and are open to considering new things, no explanation is necessary. For those that do not understand or are closed to considering new things, no explanation is possible.
You do not have to defend yourself. Let your videos speak for themselves. You may be a little over the top for some people, but your passion for vaping & for giving back are self evident.
Fooggettttabbbout it!
Just for the record I just finished with the video doing this setup in a tank and using only ONE only ONE None resistance wire.
As soon as its done uploading Ill post it.
As soon as its done uploading Ill post it.
I didn't meant that it was a fake, I was just kidding and used your famous phrase just to tell "foogetabout it" on fake videos from you and regarding a previous post on this thread. I follow you on youtube and like very much your videos.
its ok Utal thanks for clearing that up.
Posting new video now using only one N/R Wire.
Posting new video now using only one N/R Wire.
I thank you! Can't wait for your video, for now I'm enjoying a fresh twisted 1.1ohm @ 3.7v
fake video?
from Bishop?
are you crazy?
or you dont have anythink better todo?
if you knew Bishop you should NOT speak that way
HE IS A "TRUE" PERSON
from Bishop?
are you crazy?
or you dont have anythink better todo?
if you knew Bishop you should NOT speak that way
HE IS A "TRUE" PERSON
wonderful video and exellent results Manni.
I made some progress in my effort to reproduce this. Basically I just did what Bish and Imeo said. Forget about it but when it's a Bish - it's always a wrap! So I wrapped the NR around a coil just like Bish did in his video and for some reason I had around 0,8 Ohms now (which reduced to 0.6 Ohm now).
I assembled that coil in my Penelope and it works pretty good. Well after a good draw it still glows red at the joint(s) but the first draw is amazing.
Going further from there - it seems like the right track!
Bish, if you continoue to do your job as you do it right now, be sure that all people will understand what kind of person you are and they will stop making bad thoughts. You are going just great buddy!
Those of us who know Bish know very well that he has no NEED to post anything fake. He's spent endless hours experimenting with coils/mesh and different setups. Likewise he's spent endless hours helping fellow vapers learn new setups and enjoy vaping even more. If there's anything we should say to him is a big THANK YOU.
I personally don't know many members of this forum with Bish's dedication and willingness to share and help others.
Mata I would say an apology is certainly in order, don't you agree?
I personally don't know many members of this forum with Bish's dedication and willingness to share and help others.
Mata I would say an apology is certainly in order, don't you agree?
- Status
Similar threads
