GLASSMANOAK'S Contest #12 with multiple Winners!!

Status
Not open for further replies.

RayN

Ultra Member
ECF Veteran
Verified Member
Apr 10, 2012
1,444
3,398
Texas
1:
Well, the fun just never stops here.
A few weeks ago I went for an EKG and was told it was "abnormal"... not a good sign.

Yesterday my stress test showed blockage... Thursday off to the hospital for a cath lab visit and keeping my fingers crossed it can be fixed with a stent. Otherwise things will get really ugly :(
 

levisdaddy

Vaping Master
ECF Veteran
Verified Member
Aug 2, 2012
6,535
7,990
tucson
Alright guys, thanks again!
I look forward to the pics S, not sure why i have been having sooooo many issues!
The coil, is actually 1.5ohm, just retested it. I figure since i am at my desk at work, and have most everything in front of me, other than a smaller bit i might give it a go. i shoulda brought a juice i am not fond of....
--------------------------------------------------------------------------------------------------------------------------------------

FAIL.
maybe i overpacked the cotton? i cant even hear it firing inside.....
got a couple mouthful of juices, erghhhhh, draw was so tight it turned into a straw......

LD:
While risking ruining a working build, I'll take some pictures of my Fogger coil setup later tonight. Sorry I couldn't do it sooner, I'm low on time right now. Basically, do what jac said. You'll want a 1/16th drill bit for sure, it fits perfectly in the air hole. The "bottom" leg can go into a hole on the side of the insulated positive post, you may need to turn/twist it around to align the hole by using the post screw (it spins rather easily). Just make sure the length of wire doesn't go past the hole on the other side or you'll short it out on the side of the deck. For the amount of cotton ball, just fluff it out some and pack it everywhere except above, below, or in the coil. You don't really need any going out the liquid intake slits as long as it's packed right up to that area. Get some liquid on your cotton before putting the rest of it together, and of course test your coil resistance and make it glow before adding cotton or anything else. One more tip, the clear o-ring is easier to install under the chimney if you slide it down over the chimney tube once it's partially screwed on. There are pictures for all of this already, but again... short on time at the moment. Good thing I type fast! BBL, and good luck.

Complicated little atty deserves a complicated little tree pic:
hematite_pink_upright_wire_bonsai_tree_by_ken_to_by_kentoart-d6lgt14.jpg

Congrats LD! More space for munchkins is never a bad thing, and IMHO worth rearranging the budget...


You can try that micro-coil... I don't have the highest hopes for it unless you just run it normal with a cotton wick. I've really enjoyed my last Frogger build of that type. I'm loving the verts a li'l more though I've found it to be finickier... (The cotton yarn has been my best Frogger vert. Cotton balls for the 91%)


Nice flyin' JPF!!!
 

RayN

Ultra Member
ECF Veteran
Verified Member
Apr 10, 2012
1,444
3,398
Texas
@ "RayN" - Cannot "like" your post at all . . .

However, I am sending "GOOD VIBES" and I am hoping that all that is needed is a sent . . .

"YOU" Will Be In "My" Thoughts - All "My" Best To "YOU" - SIR ! ! !




BTW: Please keep "Us' updated . . . Thanks . . .:D

Yeah, you know it's not good news when they have you see the Dr immediately instead of coming back in a week.
 

jac1766

Ultra Member
ECF Veteran
Verified Member
Jul 7, 2013
1,793
3,055
The 6th circle
Happy to hear from you Ray, though I'm sorry for the content, I "liked" just because I'm glad to "see" you in the room. It could have been worse... My mother's stress test caused a direct (same day) heart cath that led directly to an awkward conversation with her doctor and an immediate trip to the OR. (6 yrs ago next week)

So... It IS good news that you were allowed to leave at all (w/o a nifty new scar).;-)

I wish you the best, I'm sure you are in good hands.
 
Last edited:

Schnarph

Vaping Master
ECF Veteran
Verified Member
Feb 21, 2013
4,618
9,558
Dripping Springs, TX
Hi Ray! Geeez guy, I'm sorry. I can't say it any better than Uncle and jac, other than to hope you make it though this ordeal. My well wishes and good vibes aren't working, but all the same... best of luck to you, sir.:nun:


For those that wanted Fogger vertical coil build info, check my blog. I hope it helps somebody. :blink:
 

Uncle

Resting In Peace
Supporting Member
ECF Veteran
Verified Member
Jun 15, 2011
32,527
116,452
Oh MY - I couldn't agre with anyone more then "Ray" right now - "the fun around here just never seems to stop" . . .

Since I will be leaving tomorrow afternoon and have limited access to the Internet for the next week, I went to check-in with another "Family" thread I belong to here on ECF only to find out some very bad and sad news about another of "My" ECF Friends . . .

So with that I am absolutely done for the day and want to say to Everyone . . .

"I Wish You Enough" . . .

Without a doubt - It's . . .
bedtime.gif
. . .

AND - I'm off . . .
gotobed.gif





Good "MoringNite" all - see Ya' all tomorrow . . .

nighttree.gif
 
Status
Not open for further replies.

Users who are viewing this thread