GLV3 Mini head

[BluSwatch]

Hey all,
I got my GLV3 Mini right before X-mas, and had a question .... I have been using it off and on without the feeder, and noticed that some things don't seem to "connect" on it ..... my joyetech atties and some cartos don't work. My Boges and madvapes DCCs work fine.
Is there something I need to do? It doesn't have a pin, so I don't see any way to make any adjustments.
Thanks -

 

[Shaitaan]

if it's a top feeder, then there is a setscrew with an orange ball inside....you put your carto or atty on and adjust the setscrew up or down for contact...sometimes it will only need a slight adjustment...my glv-3 I had ordered, has the option for both

 

[BluSwatch]

It is top and bottom feeder ..... has a hole instead if pin? Do I need to put the orange ball higher? I have been using it for top feeding, so put on carto, and tighten screw/ball ..... got it.
Thanks so much.

 

[Shaitaan]

no probs I've had mine set up for top feeding as I've been taking the mini out of the feeder quite often when I'm out and about... for bottom feeding, you wouldnt have the orange ball and setscrew in there.....just take your time and carefully adjust it to your atty or carto so you dont damage the wire going through to the post...it only needs to make slight contact, and easy to do when the atty or carto is loaded in the GLV

 

[BluSwatch]

I got extras of the allen-wrench size I needed today to keep in my kit-bag .... so I am gonna try it tonight.
Will I see a wire to the post? All I see right now is the coppery circle and a hole. LOL
Will the ball go all the way up and fill the hole? When I got it, I put the ball and set-screw in and turned them till I felt a little resistance .... I guess not enough now. But I don't see the ball from the top. It's just a little black hole (where I have a sneaking suspicion all my juice has gone ...)

 

[Tat_skull]

If you are indeed top feeding Blu, try this

1..Remove you're GLV from the feeder
2..Insert battery and cap
3..Attach a atty or carto
4..Insert allen wrench
5..Hold fire button and turn allen wrench SLOWLY till you hear it fire
6..Reattach Feeder and VAPE AWAY

Thats the method I used for stubborn adapter's and it worked like a CHARM!!
Hope you get it going

 

[BluSwatch]

Thanks! I will try that .... I haven't been using the feeder .... just the Mini part with tanks or cartos. I tried Squonking (?) but I obviously didn't know what I was doing. So I just took it off, until I can actually sit with someone and watch how it's done.

 

[Tat_skull]

On the top feeding , what I did was attach everything, then remove drip tip with tube attached, place over paper towel. Then squeeze the bottle, keep squeezing till you see the juice touch the driptip thru the tube, then count you're seconds till you see three drips!! After that just count you're seconds when liquid hit's the driptip and you should have no problems!!

 

[BluSwatch]

Ok ... I was trying to watch the juice go along the tube. That's why I think it all went in the little black hole .... guess I should take the ball out and clean it.

 

[Shaitaan]

yea there's a learning curve for it....all assembled, I usually squeeze the bottle, watch it come up the tube, then count to 4 (1 onethousand 2 onethousand 3 onethousand...). release bottle, then I blow in tip to help the juice down the tube and vape....

 

[BluSwatch]

Ok .... got wrench, cleaned out and adjust Mini .... works great! Thanks all.
Got new GLV2 Mini from classies .... thought I'd clean and adjust it also.
I was working in the bathroom for the light, and out comes a little orange ball, bouncing towards the sink (and drain)!
I didn't know the regular GLVs had orange balls ... I thought that was a bottom-feeder thing. Well I saved the ball, and got everything back together, but if worst came to worst, does Jay sell spare orange balls? LOL

 

[Tat_skull]

Glad to hear you got it working Blu