T ?
and....I NEED that G16 dripper !!!
I am so ashamed to say that I have an igo s on mine
'T', as in the Aiolos-T ma'am. I understood from your post that you were interested in the 'D' (as in Aiolos-D), I just stated the variants it is coming in.
GUS Mods Upgrade
- Thread starter aiolos
- Start date
- th_trl_thread_readers 0
- Status
'T', as in the Aiolos-T ma'am. I understood from your post that you were interested in the 'D' (as in Aiolos-D), I just stated the variants it is coming in.
1. Gus also sells 12A fuses, which are good till 0.3Ω. Or replace the fuse with a brass pin and Bob's your uncle.
2. This is a telescopic mod ~ so any size of battery can be used.
Confirming that vct4 and vct5 batts work really well in a gus kiss at .2 ohms
Poasted with my DNA30 Toaster using Sorcery
Poasted with my DNA30 Toaster using Sorcery
I have the 12 amp fuse in. I also have made a little copper pin that I use in place of it. There are other positive pins that work well with the GUS fused cap. If you look at some of the first posts in the very well done Qorax GUS Lord Review you will find some pictorials on it. I am going to be lazy and not link it. You can stop being lazy and search for it
It should be on the first or second page in the APV section.I've been interested in a GUS mod for some time now, read all these threads. I just started getting into real sub-ohm vaping a month or so ago, so I never really looked into it back then when I was originally interested in the Gus lord. Now I have ordered the Gus Kiss Summer edition v2, and hearing I gotta replace and modify all this stuff.
But I am able to get .2-.3 ohms with the standard 12a fuse it comes with? I'm sure that will be fine till I grab a brass pin.
But I am able to get .2-.3 ohms with the standard 12a fuse it comes with? I'm sure that will be fine till I grab a brass pin.
I've been interested in a GUS mod for some time now, read all these threads. I just started getting into real sub-ohm vaping a month or so ago, so I never really looked into it back then when I was originally interested in the Gus lord. Now I have ordered the Gus Kiss Summer edition v2, and hearing I gotta replace and modify all this stuff.
But I am able to get .2-.3 ohms with the standard 12a fuse it comes with? I'm sure that will be fine till I grab a brass pin.
You should be fine. You also should have ordered the spare fuse kit from Gus Mods, if not then check the Gus Lord thread there are some links to Amazon for the fuses you need.
I moved into Low Sub Ohm vaping for a while. I still keep an atty or two wound low for 2 juices that really shine at super low ohms. Other than that I have moved back up in the .8 to 1.2 ohm range. Juice lasts longer and tastes better to me there. Vapor isn't as huge but I am not trying to win any contests
This is coming to papa shortly√ Shipping on Monday
The little sister of Estia! Same principle but single wick-n-coil. No Fluff inside, No NR wire. 16mm OD ~ for our 14500 mods√
The little sister of Estia! Same principle but single wick-n-coil. No Fluff inside, No NR wire. 16mm OD ~ for our 14500 mods√
Alright, well, my Gus Kiss will be here any day now, and I'm really starting to fret about the whole fuse situation. I've never had a mechanical with fuses, usually just the brass firing pin. Is there a way I can take my brass firing pin out of a different mechanical and switch it into the GUS Kiss so I can go down to 0.1 ohms? Anywhere I could buy it online? To be honest, I don't even know how one goes about switching the fuse to the 12A fuse, or the brass pin. If I could get any help, I would be extremely grateful.
Here is my old post on it:
LORD Top-Cap Fuse Swap with other Pos Pins
Well many seem to be averse to the "Fuse" in the Gus Top-Cap and enquired whether it could be swapped with Pos Pins from other Mods. Yes absolutely, here's some pics...
Bottomline: Pretty much every mod's Positive Pin/Post (whether Telescopic or Straight Screw) can be put inside the Top-Cap of the Gus-LORD. They all seem to be threaded the same... same dimensions. And length doesn't matter since the Gus-LORd is a telescopic mod. You can thus screw it's bottom-body in to fit any Battery &/or Atty.
I hope that helped.
The fuse is really easy to change out. I've had to do it twice because the fuses that come with the Kiss don't work well for low sub-ohm builds. They do sell a fuse kit that includes higher amp fuses that do.
Well I've heard it comes with a 5A fuse, which can only handle builds down to 0.8, and the 12A fuse can handle down to 0.3ohms. I usually build my coils at 0.1, if not lower. Even 0.3 would be fine, I just don't know how to go about changing the fuse out.
Attaches any Atty onto a M20/1* threaded mod without the Mod's Top-Cap.
___________________________________________________
*Viz Gus, Paps, Caravela, Magnetic Dragon, Atom etc.
This is a Hybrid Adapter:
You just connect it onto the 510 post of your Atty (any Atty) and screw the whole thing onto your Mod directly without using the top-cap (of the mod).
These are sold by many vendors, E.g. Team Rampage, Versa Hybrid, Senio, Fusion Mods etc.
You just connect it onto the 510 post of your Atty (any Atty) and screw the whole thing onto your Mod directly without using the top-cap (of the mod).
These are sold by many vendors, E.g. Team Rampage, Versa Hybrid, Senio, Fusion Mods etc.
- Status
Similar threads
- Locked
