HARD Hitting, SMALL Mech Mod for SLR Coils

[eddiezheadiez]

Out of all my mods my Poldiacs are my favorite, when in 18350 mode it is quite small as well and hits like a champ.

I haven't given it much attention and I don't know why. It does hit all my requirements... Hmmmm you're making this decision harder now... Or easier...

Sent from my SGH-I747 using Tapatalk 2

 

[ClippinWings]

Personally it sounds like you need to try a different atomizer setup or pg/vg ratio. Switching to a mech mod and coiling a sub 1ohm atomizer isnt going to be any different than just upping the voltage on your lavatube. Maybe try switching to a higher vg blend before forking out cash on a new mod only to get the same amount of vapor.

Sorry if that sounds rude, I just think a mech mod isnt going to give you what your looking for. But, if your like me and going to buy a mech mod anyways; ive heard good things about the SupT mods and the ELA is up for preorder.

When you figure out how to get a Lavetube to pump out 23 Watts... get back to us.

Mechanical - 3.7 Volts
RBA, Dual Coiled - 0.6 Ohms

22.82 Watts
6.17 Amps

HUGE PLUMES of room filling vapor

 

[MattyB1503]

Clippin-

Hope your not pushing and AW350 that hard

 

[ClippinWings]

Clippin-

Hope your not pushing and AW350 that hard

I'm not personally, no... I think 1.0, MAYBE 0.8 is the lowest I'm comfortable with... I have seen it done and vaped off one set up as described... I will say the vape off of it was incredible.


but the fact remains... a regulated mod simply can not do it.

 

[Sweeperdk]

EA Mod with an IGO-L , 28ga kanthal with silica wick @ .7 Ω...

I can honestly say that this is beating every other RBA I have ever tried, including the AC9, DID, Mini DID and Ikarus Hybrid I have.

Small..pocketable, doesn't leak (it might have a minor leak potential once I open up the airhole a bit).

Here next to a Provari Mini in 18500 mode without top:

 

[Fury83]

Yeah, I want something relatively short. I don't really care about width so much. Could you measure it in 18350 mode for me? That would be very helpful.

Sent from my SGH-I747 using Tapatalk 2

Rather late but seems to be around 69 or 70mm with an AW IMR 18350 and my ZAU screwed flush on it. If your 510 device has a smaller connection or you use a flat top, you may be able to shave a mm or so off of it.

 

[MattyB1503]

I'm not personally, no... I think 1.0, MAYBE 0.8 is the lowest I'm comfortable with... I have seen it done and vaped off one set up as described... I will say the vape off of it was incredible.


but the fact remains... a regulated mod simply can not do it.

Yeah for 350's I wont got below .8 ohms either. I believe the maximum continuous discharging current rating is 6A for a AW IMR 18350.

Not a prob for a MNKE IMR 18650 tho.

Three two wrap with 28g and 3.5mm wick hole, I hit .9 or .8 every time

 

[aPandaz]

I'm a little late to the party...but here is a pic of my Dookz Platform in 18350 stealth mode...next to it are a water bottle, my Galaxy S4, and the wifey's iPhone 4. This thing hits...but I don't use it in this mode with the Nimbus setup the way it is...lowest I go on my 18350s is 0.8 ohm...Nimbus is dual coiled at 0.6 ohm.

 

[armalitem16]

I'm a little late to the party...but here is a pic of my Dookz Platform in 18350 stealth mode...next to it are a water bottle, my Galaxy S4, and the wifey's iPhone 4. This thing hits...but I don't use it in this mode with the Nimbus setup the way it is...lowest I go on my 18350s is 0.8 ohm...Nimbus is dual coiled at 0.6 ohm.

LOVE how this setup looks!

 

[durianeliquidflavorplease]

Oh and I have a question... Do you know why US mods use brass pins and pinoy mods use copper pins. I've read that copper is a much better conductor.

Sent from my SGH-I747 using Tapatalk 2

Mechs are pretty much the norm here in the Philippines and voltage loss is perhaps the number one concern of vapers and modders. We want as little voltage drop as possible and so we use the most conductive materials for contacts. At least that's the prevailing notion.

 

[WattWick]

Rather late but seems to be around 69 or 70mm with an AW IMR 18350 and my ZAU screwed flush on it. If your 510 device has a smaller connection or you use a flat top, you may be able to shave a mm or so off of it.

That would be 0.5mm taller than the Pisces T with an AW 18490. No idea how it performs. Just saying cause I'm puzzled as to how short it's supposed to be. Not sure if I believe it. Do want just for the size, tho.