hello,target pro

[Letitia]

another thing is that this mod is practicly my first so as far as wattage i tend to run it on has been limited due to the risk of burning the coil but i dont like the vape to be too too hot from what i can deduce from your replys and the websites items that i can find it seems to lean to vapresso nrg tank with gt8 coils but will these be weaker in vapor prudutiong than my ccell target pro tank setup?

I cannot answer that question. I primarily use rebuildables. @Fidola13 is a good one to chat about vapresso products with.

 

[chellie]

yes its the 5-75 w the mod is comfortble but tank and coils are not good in my opinion waay too sensitive coils seem to frequently be bad also the tank leaks alot which is a common issue with it aswell as the coil

I purchased the box only because I thought it looked cool with the trigger firing mechanism. Tank is way too small. I will look at your link. Any tank that will fit it should suffice.

I would second @Letitia recommendations. While mesh subohm coils provide excellent performance and decent longevity, most will use 50W of not more (not a lot more but it depends on personal preference). While your mod does provide up to 75W, you'll run into the problem of battery life. I may be wrong but I believe your mod has an internal battery, so when it's dead you have to wait for it to recharge rather than just swap in a fresh set. I'd be looking at coils that can perform well at around 30W just for the runtime, and Leticia's recommendations fit that better.

Unless there are different versions - I have the box only and it takes one 18650 battery.

 

[botox]

I purchased the box only because I thought it looked cool with the trigger firing mechanism. Tank is way too small. I will look at your link. ANy tank that will fit it should suffice.

Unless there are different versions - I have the box only and it takes one 18650 battery.

sounds about right well the nrg tank is orderd aswell as coils

 

[chellie]

I just opened mine --it is way neat. I got the purple version and it fits up to a 25mm tank with no overhang. Mod is very compact in size. From your link there are a number of tanks that would fit. Depends on your preferred choice of tank capacity. The tank I tried is 25mm the Dimensions: 2-3/4" x 15/16" (in INCHES) and 25mm Diameter so anything up to that will fit.

 

[chellie]

sounds about right well the nrg tank is orderd aswell as coils

That tank might have a little bit of overhang. It looks like it measures 26.5mm but it has a good juice capacity.

 

[Fidola13]

I cannot answer that question. I primarily use rebuildables. @Fidola13 is a good one to chat about vapresso products with.

The vapor production in all the GT Coils is fantastic in my experience. I don’t often use the GT8s anymore since I like to vape closer to .5 ohms. I usually use the GT Ccells which are ceramic. They have 2 options of GT Ccell creamics of .3 and .5 ohms. The other GT coil I love is the GT2. In addition Vaporesso has GT Mesh coils. I still prefer the ceramic or regular coils those.

Oh and one other thing the GT Ccell ceramic coils have stainless steel heating wires and are great for using in temperature control.

The Vaporesso GT coils are the only drop in coils I’ll use. I think the flavor, clouds and reliability are so good. I’ve NEVER gotten a bad GT coil in a year of using them.
Let me know if you have any other questions. Good luck!!

 

[botox]

View attachment 790783

The vapor production in all the GT Coils is fantastic in my experience. I don’t often use the GT8s that anymore since I like to vape closer to .5 ohms. I usually use the GT Ccells which are ceramic. They have 2 options of GT Ccell creamics of .3 and .5 ohms. The other GT coil I love is the GT2. In addition Vaporesso has GT Mesh coils. I still prefer the ceramic or regular coils those.

Oh and one other thing the GT Ccell ceramic coils have stainless steel heating wires and are great for using in temperature control.

The Vaporesso GT coils are the only drop in coils I’ll use I think the flavor, clouds and reliability are so good. I’ve NEVER gotten a bad GT coil in a year of using them.
Let me know if you have any other questions. Good luck!!

will do bud!

 

[botox]

I just opened mine --it is way neat. I got the purple version and it fits up to a 25mm tank with no overhang. Mod is very compact in size. From your link there are a number of tanks that would fit. Depends on your preferred choice of tank capacity. The tank I tried is 25mm the Dimensions: 2-3/4" x 15/16" (in INCHES) and 25mm Diameter so anything up to that will fit.

whatever you do stay away from the ccells from using it for 3 months ive probobly used about 40 coils where no matter how low or high the wattage is it will burn at a lower wattage then its suposed to flavor doesnt get good at all however i have heard people who are extremly happy with the ccells

 

[chellie]

whatever you do stay away from the ccells from using it for 3 months ive probobly used about 40 coils where no matter how low or high the wattage is it will burn at a lower wattage then its suposed to flavor doesnt get good at all however i have heard people who are extremly happy with the ccells

Thank-you. I do not use any of the drop in coils anymore. Stopped about a year and a half ago. I primarily use tanks with the rebuildable piece. I buy the pre-coiled coils wick it and fasten it to the rebuildable base. In the long run it is much less expensive plus I NEVER have to worry about running out of coils.

 

[Fidola13]

Thank-you. I do not use any of the drop in coils anymore. Stopped about a year and a half ago. I primarily use tanks with the rebuildable piece. I buy the pre-coiled coils wick it and fasten it to the rebuildable base. In the long run it is much less expensive plus I NEVER have to worry about running out of coils.

will do bud!

I should’ve stated that the GT coils work with the Cascade and NRG tanks which are both good. I’ve been using the Cascade Baby SE lately and it’s built like a tank. I love it!

 

[botox]

fech if one pack of coils in the usa is 10 dollar its insane here they cost 30 dollars
middleclass monthlybsalery is 1800 dollars might have to work in the usa

 

[botox]

Thank-you. I do not use any of the drop in coils anymore. Stopped about a year and a half ago. I primarily use tanks with the rebuildable piece. I buy the pre-coiled coils wick it and fasten it to the rebuildable base. In the long run it is much less expensive plus I NEVER have to worry about running out of coils.

can you just buy a premade rebuildable coil and just switch out the cotton now n then?

 

[Opinionated]

can you just buy a premade rebuildable coil and just switch out the cotton now n then?

yes, you can do that..

Advanced Vape Supply

you just have to know what coils..

 

[chellie]

can you just buy a premade rebuildable coil and just switch out the cotton now n then?

Yes - that is what a lot of us do. My coils get really gunked up because of the flavors I use so if they are not really icky I just change the cotton. If they are all gunked up - I put in a fresh coil. MUCH less expensive and in my opinion a better overall experience.

You have to have a tank that either has the rebuildable base built into the tank or some tanks are really versatile that take the store bought drop-in coils plus they have a rebuildable base that you can twist on to also have the option of using rebuildable ones.

 

[chellie]

Just as an example --- on the link you specified there are some RTA's (Rebuildable Tank Atomizers)

Here is one GeekVape Ammit 25 RTA Tank - (25 mm, 2/5 ml) - Vapes.se Sverige

Having a little issue with link but go to the site and click on RTA and then click on the Ammit

I am a little more familiar with Geekvape so I picked this one because it takes a single coil, fits your box well, has a decent juice capacity and is easy to build on. It also comes in enough colors that you can find one to match your mod box. If you go through the pictures at the link you will see what the rebuildable deck looks like.

And if you watch this video - particularly from the 3:30 mark on you will see how it is built.


It took me a while before I started to build and once I took the plunge I never looked back. You can get help from here and from watching the videos. That's what I did.

And although I do have a good amount of wire - honestly I just buy the coils in bulk - they are much less expensive than the drop-ins and once you do it a few times it is so easy to change out. You can even try different types of premade coils that way. If you are so inclined you can fully make your own.

You need cotton which is easy to get and a little stick tool to straighten out the coils. The other thing you need is either an ohms meter or you can use your vape mod to check the resistance - I will find links and post.

(Just a note --although it is not hard there are a few things that you need to know when rebuilding --you have to check the resistance and make sure the coil is installed properly. The videos cover that.)

 

[chellie]

Here are some links from fasttech because you are international and I do not know anyone that ships to you except them so here is a very basic list of what is useful. Remember you only need to get this once. Your ongoing expense is really cotton and coils......and you might even have some of these items.

Here is a very basic set of useful items if you go the rebuilding your own coils route

ceramic tipped tweezers
$2.22 Authentic Coil Father Stainless Steel + Ceramic Tweezers for E-Cigarettes at FastTech - Worldwide Free Shipping
Stick thingy for straightening out and/or winding coils
$1.52 Vaping Coil Winding Jig Tool for Rebuildable Atomizers - stainless steel / 1.5mm + 2.0mm + 2.5mm + 3.0mm + 3.5mm sections at FastTech - Worldwide Free Shipping
Small Scissors (can be used for cotton and to cut ends off of wire)
$1.30 Stainless Steel + ABS Folding Scissors for E-Cigarettes - 25mm blade length / 100mm unfolding length at FastTech - Worldwide Free Shipping
Better cutter (I use scissors for cotton and a wire cutter for wire)
$2.32 PLATO #170 Flush Cutter for Rebuildable Atomizers - max.040" (1mm) dia copper Wire at FastTech - Worldwide Free Shipping
Ohm meter (to measure coil resistance - you can also your mod instead)
$19.99 Authentic Coil Master 521 Mini V2 Tab Resistance Tester Coil Rebuilding Deck - 0.05-9.9 ohm / 1*18650 at FastTech - Worldwide Free Shipping
Premade SS316 coils (can get in a lot of places just trying to help you get started)
$3.75 316L Stainless Steel Pre-coiled Wire for RBA Atomizer (30-Pack) - 26 AWG / 0.4mm dia. / 0.7ohm at FastTech - Worldwide Free Shipping
Cotton
$4.81 Authentic GeekVape Feather Cotton Organic Cotton Wick for E-Cigarettes - 20pcs/pack at FastTech - Worldwide Free Shipping

 

[botox]

so how do i prime these gt coils can i dump em in ejuice and let them soak for abit then take em out and let them sit in and dry of?next question is what setting should i run the gt coils on wattage,ss etc
ill look into the rebuildable sometime in the future thanx!

 

[botox]

so update on this issue i got sick of the ccell they where never ever good after going through like 5-10 5 packs and trying absulutly EVERYTHING sugested soo i ended up getting a nrg tank instead hopefully thats better also i found out that the battery ive been using isnt by a well known brand soo that could also be the cause got new ones now if coils that are suposed to be able to take higer wattage then 20 and it burns the coils at 20 something is defenitivly wrong

 

[bombastinator]

so update on this issue i got sick of the ccell they where never ever good after going through like 5-10 5 packs and trying absulutly EVERYTHING sugested soo i ended up getting a nrg tank instead hopefully thats better also i found out that the battery ive been using isnt by a well known brand soo that could also be the cause got new ones now if coils that are suposed to be able to take higer wattage then 20 and it burns the coils at 20 something is defenitivly wrong

I would suspect coil priming. Or possibly the mod. Even a crap battery shouldn’t change voltage. It’s detected and regulated by the mod.

 

[classwife]

Merged your 2 threads